Troubleshooting - Fender FWG 1010 Manual De Instrucciones

PROBLEM POSSIBLE CAUSE
No sound 1. AC adapter is not connected to receiver and/or power outlet.
2. Receiver is OFF.
3. Receiver is not connected to mixer or amplifier.
4. VOLUME control on receiver is at zero.
5. Instrument is not connected to pocket transmitter.
6. Transmitter has a different frequency range or is tuned to a different frequency
7. Transmitter on/off switch is at "OFF" or "MUTE".
8. Transmitter batteries are not inserted properly.
9. Transmitter batteries are dead.
10. Transmitter is too far away from receiver or squelch level set too high.
11. Obstructions between transmitter and receiver.
12. No line of sight between transmitter and receiver.
13. Receiver is too close to metal objects.
Noise, crackling, unwanted signals. 1. Antenna location.
2. Interference from other wireless systems, TV, radio, CB radios, or defective electri-
Distortion. 1. GAIN control on transmitter is set too high or too low.
2. Interference from other wireless systems, TV, radio, CB radios, or defective electri-
3. Antenna location.
Carrier frequencies
Switching band width up to
Modulation
Audio transmission bandwidth
Total harmonic distortion at 1 kHz
Signal/S/N ratio
Transmission power
Voltage supply
Operating time
Squelch threshold
Audio output
Dimensions:
Weight:
Only for frequency bands designed for use in the EC: This product corresponds to the standards stated in the Declaration of Conformity.
5
FWG

Troubleshooting

from the receiver.
cal appliances or installations.
cal appliances or installations.
Specifications
RECEIVER
530.025-559.000 MHz (Band A)
826.300-831.000 MHz (Band M)
863.100-864.900 MHz (Band D)
30 MHz (Depends on the used frequency band)
FM
40 - 20,000 Hz
typ. 0.8%
typ. 105 dB(A)
–
Power supply unit 12 V / 500 mA (or via antenna splitter)
–
-100 to -70 dBm, adjustable
XLR symmetric and 1/4" (6.3 mm) jack plug asymmetric: Adjust-
able from microphone to line level. Output level at rated trav-
el: 500 mV eff.
200 x 150 x 45 mm (without antennas)
373 g
1010
REMEDY
1. Connect AC adapter to receiver and/or power outlet.
2. Push ON/OFF switch to switch receiver ON.
3. Connect receiver output to mixer or amplifier input.
4. Turn up VOLUME control.
5. Connect instrument to audio input on the pocket transmitter.
6. Use a transmitter with the same frequency range as the receiver or tune
both to the same frequency.
7. Set transmitter on/off switch to "ON".
8. Insert batteries conforming to "+" and "-" marks.
9. Replace transmitter batteries.
10. Move closer to receiver or reduce squelch level.
11. Remove obstructions.
12. Avoid spots where you cannot see receiver.
13. Remove interfering objects or move receiver away from them.
1. Relocate receiver or antennas.
2. Switch off interference sources or defective appliances or tune transmitter
and receiver to a different frequency; have electrical installation checked.
1. Decrease or increase GAIN setting just enough to stop the distortion.
2. Switch off interference sources or defective appliances or tune transmitter
and receiver to a different frequency; have electrical installation checked.
3. Relocate receiver or antennas. If dead spots persist, mark and avoid them.
TRANSMITTER
530.025-559.000 MHz (Band A)
826.300-831.000 MHz (Band M)
863.100-864.900 MHz (Band D)
30 MHz (Depends on the used frequency band)
FM
40 - 20,000 Hz
typ. 0.8%
typ. 105 dB(A)
10 mW, 50 mW (Depends on the used frequency band)
1x 1.5 V battery size AA
6 - 8 h (Depends on RF power used)
–
–
60 x 74 x 30 mm
60 g