Safety Devices - Elettro PLASMA 1880 SYNERGIC Manual De Instrucciones

INSTRUCTIONS FOR PLASMA CUTTING MACHINE
E) SUGGESTED CUTTING SPEED (only in mechanized cutting):
Once the thickness and the kind of material to be cut are specified, the machine displays the suggested cutting speeds, the value indicated after the letter
"q" (Pict. 4 Ref. E) is the suggested speed for a quality cut, the value indicated alter the letter "m" (Pict. 4 Ref. E), on the contrary, is the suggested speed for
production in quantity.
F) SUGGESTED NOZZLE:
This icon (Pict. 4 Ref. F) tells you what nozzle size to use, the value is set automatically based on the cutting current.
G) CUTTING CURRENT:
Selecting this icon (Pict. 4 Ref. G) it is possible to modify the cutting current. In automatic mode the machine will suggest a cutting current accordingly to the
thickness, the kind of material to be cut and the cutting speed (with thickness changes the machine always proposes maximum current, thereby achieving
the highest possible productivity and cutting speed).
H) CUTTING GAS PRESSURE:
The icon tells you whether the system is in automatic or manual gas regulating mode, in the latter case it is possible to select the icon and change the
pressure value at your discretion, the cutting pressure will appear on the screen in real time.
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES
MANUAL CAREFULLY BEFORE INSTALLING, USING,
OR SERVICING THE MACHINE, PAYING SPECIAL
ATTENTION TO SAFETY RULES. CONTACT YOUR
DISTRIBUTOR IF YOU DO NOT FULLY UNDERSTAND
THESE INSTRUCTIONS.
This machine must be used only for cutting, gouging and
marking operations.
It is also essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must
be stored carefully in a place familiar to everyone involved
in using the machine. They must be consulted whenever
doubts arise and be kept for the entire lifespan of the
machine; they will also be used for ordering replacement
parts.
1. INSTALLATION
1.1. TORCH ASSEMBLY
This machine is suitable to work only with a genuine
ELETTRO C.F. torch. We do not assume any
responsibility in case that a different kind of torch is
used.
Insert the torch onto the fitting S3 (see Pict. 1) using the
special tool supplied, firmly tightening the ring-nut to avoid
air leaks that could damage or interfere with smooth
operation of the torch.
Do not dent the current pin or bend the pegs of the torch
fitting. A dented pin may not disconnect, while a bent peg
does not allow proper insertion onto the fixed fitting S3
(Pict. 1), thereby preventing the machine from working.
The power source is able to automatically recognise which
torch is installed and adjust automatically when the power
DISPLAY S2 LEGEND
A) CUTTING MODES:
Selecting this icon (Pict. 4 Ref. A) it is possible to choose the cutting
mode desired.
B) MATERIAL TO BE CUT
Selecting this icon (Pict. 4 Ref. B) it is possible to choose the kind of
material to be cut among iron, aluminium and stainless steel.
C) THICKNESS OF MATERIAL:
Selecting this icon (Pict. 4 Ref. C) it is possible to set the thickness of
the material to be cut, once this value is specified, the machine will
adjust accordingly the other parameters as the current and the cutting
speed.
D) SIGNAL TRANSFERRED ARC:
4
When this icon (Pict. 4 Ref. D) lights up, it means that the machine is on
and is working.
is switched on.
Below is a list of the torches that are automatically
recognised by the single power sources:
Power source
1.2. DESCRIPTION OF DEVICES ON THE MACHINE
(Pict. 1)
S1) Selection and regulation Encoder knob
S2) Display
S3) Torch fitting
S4) Grounding clamp
S5) Pressure regulator knob (only in item 453)
S6) Pressure gauge (only in item 453)
S7) Compressed air fitting
S8) Mains power switch
S9) Power cord
S10) Inlet gas filter
S11) CNC interface kit (optional in art.453)

1.3. SAFETY DEVICES

This system comes equipped with the following safety
devices:
Overload cut-out:
To avoid overloads.
Pneumatic:
Located on the torch inlet to prevent low air
15
Item 461 Item 453
ECF-71 ECF-71
ECF-131
ECF-181 ECF-181