Kenmore 110.26132410 Manual De Uso página 18

First try the solutions suggested here for assistance and to possibly avoid a service call�
If you experience
Washer not performing as expected (cont.)
Incorrect dispenser
operation
Powdered detergent
not dissolving completely
in load
Single-dose laundry
packet not dissolving
Error Code Appears in Display
LF (too long to fill) or
F8E1 appears in display
"--"
F## code (F-type error
code) appears in display
F1E1 ACU (appliance
control fault)
F2E3 UI/ACU mismatch
F3E1 Water level sensing
failure
F5E2 Lid lock will not
lock if lid lock failure
F5E3 Lid cannot unlock
F6E2 or F6E3
Communication Error:
UI cannot communicate
F8E6 code (water
hazard) will appear
in display
"drn" "dr" (F9E1) (drain
pump system problem –
long drain) appears in
display
"Ofb" (Off Balance)
18
TROUBLESHOOTING
Possible Causes
Clogged dispensers or laundry
products dispensing too soon�
Liquid chlorine bleach not used
in dispenser�
Using too much HE detergent�
Water temperature is very cold�
Adding laundry packet incorrectly�
Washer taking too long to fill. Drain
extends more than 4.5" (114 mm) into
standpipe�
Water supply not connected or
turned on�
Cycle knob is not on cycle�
System error code�
Internal ACU failure�
UI/ACU initialization error�
Pressure sensor on ACU failure�
An item in the load may be keeping
the lid from locking�
Objects on washer lid prevent it from
unlocking�
ACU or UI synchronization error�
Lid is left open for more than
10 minutes and water has
pumped out�
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm) into standpipe.
Load not balanced or evenly
distributed around the basket�
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select Fabric Softener option to ensure proper dispensing�
Load dispensers before starting a cycle�
It is normal for small amounts of water to remain in dispenser
at the end of the cycle�
Homes with low water pressure may result in residual powder
in the dispenser� To avoid, select a warmer wash temperature
if possible, depending on your load�
Use only liquid chlorine bleach in the bleach dispenser�
Follow the manufacturer's instructions to determine the amount
of detergent to use�
Select a warmer wash temperature�
Try adding the detergent to the basket prior to adding laundry,
rather than using the detergent dispenser�
Be sure laundry packet is added to washer basket before adding
clothes� Follow the manufacturer's instructions to avoid damage
to your items�
Check plumbing for correct drain hose installation� Use drain hose
form and attach securely to drainpipe or tub� Do not tape over
drain opening� See Installation Instructions�
Check water supply to make sure hoses are connected and/or
turned on�
This is not an error� The selector knob is not on a cycle� Rotate
your selector knob until a cycle lights up�
Touch the Start/Pause/Unlock Lid button once to clear the code�
Then touch the Start/Pause/Unlock Lid button again to restart
washer� If code appears again, call for service�
Call for service�
Call for service�
Call for service�
Check for items directly under the lid�
Remove objects, such as baskets of laundry, from top of washer�
Remove power from the washer� Let washer set for 5 minutes for
the washer to completely power down� Apply power to washer
and check for error codes� If the error code persists, call for
service�
Make sure lid is closed before starting a cycle and/or during
prewash (soak).
Check plumbing for correct drain hose installation� Use drain hose
form and attach securely to drainpipe or tub� Do not tape over
drain opening� See Installation Instructions�
Check plumbing for correct drain hose installation� Use drain hose
form and attach securely to drainpipe or tub� Do not tape over
drain opening�
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See Installation
Instructions�
Cycle is paused as indicated by the flashing Start/Pause/Unlock
Lid indicator� Open the lid, redistribute the load, and close the lid�
Touch and hold the Start/Pause/Unlock Lid button to resume�
Solution