Idiomas disponibles
Idiomas disponibles
14 | English
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions. Only use saw blades
with a single lug shank (T shank) or with a 1/4" universal
shank (U shank). The saw blade should not be longer than
required for the intended cut.
Use a narrow saw blade when sawing tight curves.
Inserting the saw blade (see figure A)
Clean the shaft on the saw blade before inserting it.
u
A dirty shaft cannot be securely fixed in place.
Loosen the saw blade fastening screw (8) using the hex
key (4) provided.
Push the saw blade (10), with the teeth in the cutting direc-
tion, into the saw blade receptacle (13) ➊ until it clicks into
place.
Make sure when inserting the saw blade that the back of the
saw blade is in the groove on the guide roller (9).
Firmly tighten the screw (8) with the hex key (4) ➋.
Check that the saw blade is seated securely. A loose
u
saw blade can fall out and lead to injuries.
Removing the saw blade (see figure B)
Unscrew the saw blade fastening screw (8) ➊ and remove
the saw blade (10) ➋.
Anti-splinter guard (accessory) (see figure C)
The anti-splinter guard (15) (accessory) can prevent splin-
tering of the surface while sawing wood. The anti-splinter
guard can only be used with certain saw blade types and only
at a cutting angle of 0°. When sawing with the anti-splinter
guard, the base plate (7) must not be moved to the rear for
sawing close to edges.
Push the anti-splinter guard (15) into the base plate (7)
from below.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
1 609 92A 89P | (22.11.2022)
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Hood
Fit the hood (12) before you connect the power tool to the
dust extraction system.
Position the hood (12) on the power tool so that the brack-
ets click into place in the recesses on the housing.
Remove the hood (12) when working without a dust extrac-
tion system and for mitre cuts. To do this, push the hood to-
gether at the level of the outer brackets and remove it by
pulling it forwards.
Connecting the dust extraction system
Connect a dust extraction hose (5) (accessory) to the ex-
traction outlet (6). Connect the dust extraction hose (5) to a
dust extractor (accessory).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
For optimum dust extraction, where possible use the anti-
splinter guard (15).
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Operating modes
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Adjusting the mitre/bevel angle (see figure D)
The base plate (7) can be swivelled to the right or left to
make mitre cuts up to 45°.
The anti-splinter guard (15) cannot be used while mitre cuts
are being made.
– Remove the anti-splinter guard (15).
– Loosen the screw (16) and push the base plate (7)
slightly towards the mains cable.
– The base plate has lock-in points at 0° and 45° on the left
and right so that precise mitre/bevel angles can be set.
Swivel the base plate (7) to the desired position accord-
Bosch Power Tools
