Idiomas disponibles
Idiomas disponibles
Mount the baby unit on dry wall (optional)
Not Included
You will need to purchase the following
items separately to mount your baby unit:
2 screws
2 anchors
Note
NOTES
NOTE
• The types of screws and anchors you need
depend on the composition of the wall.
Note
NOTES
NOTE
• Check for reception strength and camera
angle before drilling the holes.
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
Drill two holes in the wall (5.5mm drill bit ). If
you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the wall anchors into the holes.
Tap gently on the ends with a hammer until
the wall anchors are flush with the wall.
Insert the screws into the holes
and tighten the screws until only
6.5mm of the screws are exposed.
Align the wall mount holes on the
baby unit with the screws on the
wall. Slide the baby unit down
until it locks into place.
Adjust the camera angle.
14
Frequently asked questions
Below are the questions most frequently asked about the baby monitor.
Why does the
Try the following (in the order listed) for common cure:
baby monitor
1. Disconnect the power to the baby unit and the parent unit.
not respond
2. Wait a few seconds before connecting power back to the baby unit and the parent
normally?
unit.
3. Turn on the baby unit and the parent unit.
4. Wait for the parent unit to synchronise with the baby unit. Allow up to one
minute for this to take place.
Why doesn't the
Perhaps the parent unit is not connected to the power. Insert the adapter plug into
the parent unit and insert the adapter in a wall socket. Then, press and hold
baby unit and parent
unit power-on light
POWER to switch on the parent unit to establish connection with the baby unit.
illuminate when the units
Perhaps the baby unit is not connected to the power. Insert the adapter plug into
are switched on?
the baby unit and insert the adapter in a wall socket. Then, establish a connection
with the parent unit.
Why doesn't my parent
Make sure the power is not controlled by an electronically controlled wall switch.
unit charge while
The battery may de degraded through extended use or defective. See Warranty
connected to AC power?
for repair/replacement.
Why is my screen in
The screen is in black and white during night-time or in a dark room when the night
black and white?
vision feature is activated. This is normal.
Why do I get glare or
During night-time or in a dark room, the surroundings and other interfering factors,
blurry display on my
like lighting, objects, colours and backgrounds may affect the image quality on your
screen when viewing my
parent unit screen. Adjust the baby unit angle or place the baby unit at a higher
baby at night?
level to prevent glare and a blurry display.
Why does the baby
The parent unit and baby unit may be too close to each other.
monitor produce a
• Move the parent unit away from the baby unit until the noise stops; OR
feedback noise?
• Turn down the volume of your parent unit.
Why does the parent
The baby unit may be out of range. Move the parent unit closer to the baby unit
unit beep?
(but not less than 1 metre).
The parent unit may not have enough charge for the parent unit to perform
normally. Charge the battery in the parent unit until the battery icon segments are
solid
.
The temperature of your baby's room may be too high or too low.
Why does the parent
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
unit react too quickly to
sensitivity level to a lower level or lower the parent unit speaker volume.
other sounds?
Why don't I hear a
The parent unit speaker volume may be too low. See Adjust parent unit speaker
sound/Why can't I hear
volume to increase the volume.
my baby cry?
Why can't I establish a
The baby unit may be out of range. Move the parent unit closer to the baby unit
connection? Why is the
(but not less than 1 metre).
connection lost every now
Other electronic products and wireless products may cause interference with your
and then? Why are there
baby monitor. Try installing your baby monitor as far away from these devices as
sound interruptions?
possible.
15
