Idiomas disponibles
Idiomas disponibles
substances: Ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use only suitable accessories. In this way, fewer
particles enter the environment in an uncontrolled
manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and
keep it clean using a vacuum cleaner. Sweeping
or blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush.
5. Overview
See page 2.
1 LED lights
2 Release lever
3 Slide switch
4 Handle
5 Setting wheel for speed adjustment *
6 Battery pack
7 Battery pack release button
8 Extractor connection piece *
9 Dust extraction *
10 Adapter for FEIN
11 Capacity indicator button *
12 Capacity and signal indicator *
13 Gear box flange
14 Tool holder
15 Accessories *
16 Spring pin
17 Sanding disc *
*depending on the features / model
6. Commissioning
Battery pack
Charge the battery pack (6) before use.
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
Li-Ion battery packs "Li-Power" have a capacity and
signal indicator (12):
- Press the button (11), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
®
-tools *
Removing and inserting the battery pack
Removal: Press the battery pack release (7) button
and pull the battery pack (6) upwards.
Inserting: Slide in the battery pack (6) until it
engages.
7. Use
7.1
Attach dust extraction (only when working
with triangular sanding plate)
See Fig. A, page 2
- Remove (15) tools.
- Place the dust extraction (9) onto the gear box
flange (13):
In section "B" the extraction can be moved freely.
When placing the extraction in position "A" it is
secured against twisting.
- Connect a suitable extraction unit with its
extraction hose to the inserted intake socket (8) .
7.2
Attaching the accessory
Prior to any conversion work: Remove battery
pack from machine.
Danger of injury due to the sharp accessories.
After stopping work, the tool may still be hot.
Danger of crushing when changing the tool. Wear
protective gloves.
Use only accessories with an OIS holder or a
compatible holder.
Use only sharp, undamaged saw blades. Do
not use accessories that are cracked or that
have changed their shape. Use an accessory that is
suitable for the material being sawn.
See Fig. A, page 2.
1. Open the release lever (2) until the stop.
2. Remove the spring pin (16) .
3. Place the accessory (15) in the desired position
onto the tool holder (14) . Ensure that it engages
in the cams of the tool holder (14) .
4. Insert the spring pin (16) until the stop.
5. Caution! The clamping lever (2) can snap back
and crush your fingers. Handle with care. Wear
protective gloves.
Close the release lever (2) until the stop and
lock. (The release lever has to be in contact with
the housing).
6. Check the accessories for firm hold.
®
Note: For FEIN
-accessories place the supplied
adapter (10), as shown, on the tool holder (14) . See
figure, page 2.
7.3
Installation of sanding disc
Simple attachment and removal thanks to the
velcro-type fastening. Simply press on the sanding
disc (17) such that the holes in the sanding disc are
aligned with the support plate.
7.4
Switching On and Off
Switch on first, then guide the accessory
towards the workpiece.
ENGLISH en
9
