Tabla de contenido
Idiomas disponibles
Idiomas disponibles
• If the
brake
is already
activated,
it is
disengaged
by pulling the froet hand guard
back
toward
the front handle
as far as
possible.
• When cutting with the saw, the chain brake
must be disengaged.
Disengaged
,_
Braking
function
control
CAUTION:
The
chain
brake
must
be
checked several times daily. The engine must
be running when performing
this procedure,
This is the only instance when the saw should
be placed on the ground with the engine run-
ning.
Place the saw on firm ground,
Grip the rear
handle with your right hand and the front han-
dle with your left hand. Apply full throttle
by
fully depressing
the throttle trigger.
Activate
the chain
brake by turning
your
left wrist
against
the
hand guard
without
releasing
your grip around the front handle,
The chain
should
stop immediately,
Inertia
activating
function
control
_I_WARNING:
When
performing
the
following
procedure,
the
engine
must
be
turned off.
Grip the rear handle with your right hand and
the front handle with your left hand,
Hold the
chain saw approximately
14" (35 cm) above
a stump
or other wooden
surface.
Release
your
grip on the front handle and use the
weight of the saw to let the tip of the guide bar
fall forward and contact the stump. When the
tip of the bar hits the stump, the brake should
activate.
IMPORTANT
POINTS
• Check chain tension
before first use and
after 1 minute of operation.
See CHAIN
TENSION
in the ASSEMBLY
section,
• Cut wood only.
Do not cut metal, plastics,
masonry,
non-wood
building
materials,
etc.
• Stop the saw if the chain strikes
a foreign
object,
Inspect
the saw and repair or re-
place parts as necessary,
• Keep the chain out of dirt and sand.
Even a
small amount of dirt wilt quickly dull a chain
and thus increase the possibility of kickback.
• Practice
cutting a few small logs using the
following techniques
to get the "feel" of us-
ing your
saw before
you begin
a major
sawing
operation,
•
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting,
•
Begin
cutting
with
the
saw
frame
against the log,
•
Keep the engine at full speed the entire
time you are cutting.
•
AIIowthechaintocutforyou.
Exertonly
light downward
pressure,
If you force
the cut, damage to the bar, chain, or en-
gine can result.
•
Release
the throttle trigger as soon as
the cut is completed,
allowing
the en-
gine to idle.
If you run the saw at full
throttle without a cutting load, unneces-
sary wear can occur to the chain, bar,
and engine.
•
To avoid losing control when cut is com-
plete, do not put pressure
on saw at end
of cut.
• Stop the engine
before
setting
the saw
down after cutting,
TREE
FELLING
TECHNIQUES
_WARNING:
Check for broken
or
dead branches
which
can fall while cutting
causing
serious injury, Do not cut near build-
ings or electrical
wires if you do not know the
direction
of tree fail, nor cut at night since you
will not be ale to see well, nor during
bad
weather such as rain, snow, or stroeg winds,
etc. if thetree
makes
contact with any utility
line, the utility company
should
be notified
immediately.
• Carefuliyplanyoursawingoperation
inad-
vance.
• Cleartheworkarea,
You needacieararea
all around the tree so you can have secure
footing.
• Study
the
natural
conditions
that
can
cause the tree to fall in a particular
direc-
tion.
Natural
conditions
that can cause a tree to
fall in a particular
direction
include:
• The wind direction
and speed.
• The lean of the tree.
The lean of a tree
might not be apparent
due to uneven
or
sloping terrain,
Use a plumb or level to de-
termine the direction
of tree lean.
• Weight and branches
on one side.
• Surrounding
trees and obstacles.
Look for decay and rot, ffthetrunk
is rotted,
it can snap and fall toward
the
operator.
Check for broken
or dead branches
which
can fall on you while cutting.
Make sure there is enough room for the tree
to fall.
Maintain
a distance
of 2-1/2 tree
lengths from the nearest person or other ob-
jects, Engine noise cae drown out a warning
sail
Remove
dirt, stones,
loose bark, nails, sta-
ples, and wire from the tree where cuts are to
be made.
Plan a clear retreat path to the rear and diag-
onal to the line of fall.
11
Tabla de contenido
