Idiomas disponibles
Idiomas disponibles
Air supply:
Via a compressed air source with pressure setting
function, e.g. a compressor. Before starting up,
please also read the section on care and mainte-
nance.
Performance values of the compressor:
The compressor used should have a tank volume
of at least 50 liters.
Setting values for work with the suction
spray gun:
Set a maximum working pressure of 6.3 bar at
your compressed air supply.
5.1 Lubricating the tool
Each time before starting and during prolonged
operation:
•
Insert 3-5 drops of special compressed air oil
into the compressed air connection (6) (not
included in delivery)
•
Let the equipment run briefly so that any sur-
plus oil is blown out.
5.2 Fitting the nipple (Fig. 3-3a)
Raise the protective cap carefully with a suitable
tool such as a screwdriver. Then fasten the nipple
(6) to the air connection (11) by screwing it tight
with a suitable screwdriver.
5.3 Fitting/removing the grinding disk holder
(Fig. 4-5a)
•
Undo the clamp nut (1).
•
Guide the grinding disk holder (14) into the
clamp (2).
•
Make sure that the clamping length is at least
10 mm.
•
Tighten the clamp nut (1) using the two chuck
keys.
•
Check that the grinding disk holder (14) is
securely seated.
5.4 Fitting the grinding disk (Fig. 6)
Fasten the grinding disk (12) on the shaft of the
grinding disk holder (14) and secure it with the
chuck key.
Always make sure that the grinding disk and the
grinding disk holder are securely seated!
5.5 Fitting the abrasive paper (Fig. 7-7a)
Secure the abrasive paper (13) by means of the
hook-and-loop fastener on the grinding disk (12).
When working on uneven surfaces you can use
the intermediate disk (15).
Anl_TC_PA_50_SPK13.indb 15
Anl_TC_PA_50_SPK13.indb 15
GB
6. Operation
6.1 Connecting to a compressed air supply
•
Connect the nipple (6) to the quick-lock coup-
ling of a compressed air hose (the hose is not
supplied).
•
Note the maximum permissible operating
pressure of the equipment.
6.2 Switching on and off (Fig. 1)
Switching on: Push the safety lock-off (5) for-
wards, then press the operating switch (4) down.
Switching off : Let go of the operating switch (4)
6.3 Working with the pneumatic angle grinder
Warning! The workpiece you want to grind must
never be held in your hand. Secure the workpiece
on a sturdy surface or with a vise.
•
Place the whole surface area of the grinding
disk on the material.
•
Switch on the machine and move it with gent-
le pressure over the workpiece, making circu-
lar or transverse and linear movements.
•
Use a coarse grit for coarse grinding and a
finer grit for finish grinding. You can find the
best grit size for the job by carrying out grin-
ding tests.
Danger!
The dusts which are formed while the equipment
is being used may be a health hazard:
•
Always wear safety goggles and a dust mask
during grinding work.
•
All persons who work with the equipment or
enter the workplace must wear a protective
dust mask.
•
Eating, drinking and smoking are prohibited
at the workplace.
•
Paints containing lead are not allowed to be
used!
7. Cleaning, maintenance and
ordering of spare parts
Disconnect the compressed air supply from the
equipment before performing any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
- 15 -
07.12.2023 13:13:28
07.12.2023 13:13:28
