Idiomas disponibles
Idiomas disponibles
USE
CONTROL RECHARGE
Connect the USB cable supplied with the control to a certified 5
Volt socket.
Wait for the LED to turn solid green.
IN CASE OF FAILURE
Follow the New Code Assignment procedure (A + D + E). Then
disconnect and reconnect the hood to the mains and repeat the
Affiliation procedure (B + E). Refer to control function table.
This product is designed to work with an Elica remote control,
either supplied with the product or purchased separately as an
optional.
To control the hood via remote control, the affiliation procedure
must be carried out.
CAUTION
I
To begin, the hood must be disconnected and then reconnected
to the power supply and the affiliation procedure must be carried
out within the first minute of connection to the power.
Note: the Speed 4 (and the Speed 5, where applicable) if selected,
will activate for a limited period of time after which Speed 2 is
automatically enabled.
REMOTE CONTROL CONNECTION (if applicable)
Once the remote control has been connected, this will be
displayed on the hood: both LEDs flash.
Note: Using the remote control, delayed shut-down can be
programmed based on the aspiration speed (power) enabled
at that moment:
•
Speed 1 (low aspiration): 20 minutes
•
Speed 2 (medium aspiration): 15 minutes
•
Speed 3 (high aspiration): 10 minutes
FILTER SATURATION INDICATOR LIGHTS
At regular intervals, the LEDs on the hood indicate the need to
carry out filter maintenance.
Note: The filter saturation signal is visible for a few seconds when
the hood is switched on; within this time, the saturation indicator
lights must be reset.
Flashing Green LED: carry out maintenance on the grease filter.
Red flashing LED: carry out maintenance on the charcoal
filter (only for hoods operating in "Filtration Version").
Note: Run the "RESET FILTRES" command via the remote control.
ACTIVATING/DEACTIVATING THE FILTER SATURATION
INDICATOR LIGHT
Note: Run the procedure with the hood switched off. The charcoal
filter saturation indicator light is usually deactivated.
If no control is given within maximum 10 sec, the hood automati-
cally exits this function, at any time, and returns to the previous
state.
Press and hold the B+C keys (Simultaneously) to enter
the setup menu:
•
Briefly press button C to select the filter to be set up:
•
Grease filter:Green
•
Charcoal filter: Red
•
Briefly press button B to activate (the 2nd LED flashing) or
deactivate (2nd LED off).
Note: the LEDs light up for a limited number of seconds
after which they turn off to indicate that the indicator light
has been activated (or deactivated).
SAFETY INFORMATION
Use the remote control with care; it contains delicate electronic
parts. The remote control may be damaged if dropped, burned,
pierced or crushed, or it comes into contact with liquid substances.
Do not open the remote control is dissembled, it may be dama-
ged.
BATTERY
Do not attempt to replace the remote control battery using your
own initiative, as it may be damaged.
This certificate attests that this remote control is in compliance
with the essential requirements and other pertinent dispositions
established by Directive RED 2014/53/EU. The. Declaration of
Conformity can be viewed at. the following link:
http://elica.com/DeclarationOfConformity.pdf
CONFORMITY
Elica remote control complies with the following requirements:
FCC (Federal Communications Commision) Part 15.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modification not expressly approved by the party res-
ponsible for compliance could void the user's authority to operate
the equipment.
Note 1: This equipment has been tested and fiund to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC rule. These limits are designed to provide reasonable pro-
tection against harmful interference in a residencial installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance.
However, there is no guarantee that interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try correct the
interference by one or more of the following measure:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different
•
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
•
help.
DISPOSAL WARNING
Do not dispose of electrical products in the general waste and en-
sure the used product or batteries are disposed safely according
to your local authority and regulations.
11
