Idiomas disponibles
Idiomas disponibles
Intended use
This product is an accessory optic for the „Orbiter" luminaire. It
is intended to illuminate persons and objects in long throw
applications.
Always follow the safety information.
Any usage other than described above is not permitted. It can
damage the product and lead to associated risks such as
short-circuit, fire, electric shock, etc. You are not allowed to
modify the product.
This product fulfills all legal requirements.
Safety Instructions
•
Please read and observe all instructions delivered with the
product before use. The instructions contain important
information for safe handling.
•
Please follow the safety information in the ARRI safety
leaflet Operating your ARRI lampheads safely. It is
available for free download on the ARRI website
www.arri.com.
•
Please keep all instructions delivered with the product for
possible subsequent owners.
The user must:
•
Be qualified for the appropriate use of the accessory.
•
Follow the user manual.
•
Ensure safe usage.
•
Use the product in accordance with regulations.
•
Follow the latest regulations and standards.
Caution! Hot reflectors. Risk of skin burns.
The reflectors are hot when in use. Never touch
a reflector to avoid skin burns.
Advice. Sensitive surface.
Never touch the reflectors with bare skin as
grease,
perspiration
destroy the sensitive surface of the reflectors
within a short time.
ARRI is not liable for damages caused by improper use or
incorrect operation.
To Mount the Orbiter Beam
•
Loosen the snoot and remove the snoot.
•
Mount the snoot facing away from the Quick Lighting Mount
and fasten three snoot fixing screws (4).
•
Secure the snoot with a suitable safety cable. Pass the
safety cable through the handle (9) of the reflector assembly
and one of the safety loop attachments (10) of the snoot.
•
Remove the protective cap from the Quick Lighting Mount.
•
Align the locking pin (8) with the guide for the locking pin
(12). Insert the Orbiter Beam in the Quick Lighting Mount.
•
Turn the Orbiter Beam clockwise, until the locking slider
(11) audibly engages.
•
Secure the Orbiter Beam with a suitable safety cable. Pass
the safety cable through the safety loop attachment (9) and
the upper handle of the Orbiter.
Caution! Risk of falling components.
Always secure the Orbiter Beam against falling
with a safety cable if the primary catch fails!
To Focus the Light Beam
•
Adjust the focus with the thumb screw (3).
and
moisture
might
Automatic Optic Recognition
The digital optics interface of the Quick Lighting Mount
recognizes the optic attached to the luminaire. It adapts the light
output for best performance of the attached optic.
If the digital optics interface fails to recognize the attached optic
correctly, please clean the contacts. The procedure is described
in the Orbiter Safety and Installation Manual. It is available for
free download on the ARRI website www.arri.com.
To Remove the Orbiter Beam Optic
•
Remove the safety cable from the Orbiter Beam.
•
Push the locking slider (11) inwards. Turn the Orbiter Beam
counterclockwise until it stops.
•
Remove the Orbiter Beam. Place the protective cap on the
Quick Lighting Mount.
•
Remove the safety cable between the snoot and the
reflector assembly.
•
Loosen three snoot fixing screws (4) and remove the tube.
•
Mount the snoot facing away from the reflector and fasten
three snoot fixing screws (4).
Maintenance and Cleaning
Inspect the product regularly for visible damage.
•
Do not use a damaged or deformed product.
•
Do not use a product with a defective safety loop
attachment or safety cable. Repair the defective component
immediately.
•
The coating of the reflectors is extremely sensitive. Only
clean the reflectors with dry, oil-free compressed air at low
pressure. Gently dab off stuck particles with a cotton swab
moistened with a mild detergent.
•
Clean the housing with a mild detergent and a soft cloth.
ARRI Service
In case of technical problems please visit us at:
www.arri.com
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Global Application & Services
Flintsbacher Strasse 1-5
D-83098 Brannenburg
Germany
Design and specifications are subject to change without notice.
3
