Media; Ribbon - TOSHIBA TEC Corporation B-670 Serie Manual De Instrucciones

2. SPECIFICATIONS

2.3 MEDIA

Stop
position
Cut
position
Item
Span of one label/tag
A :
: Label length
B
: Width including backing paper
C
: Label width
D
: Gap length
E
: Black mark length (Tag paper)
F
: Effective print width
G
:
H
Effective
print length
: Print speed up/slow down area
I
: Black mark length (Label)
J
Maximum effective
length for on the fly
isue
Outer roll diameter
Thickness
NOTES:
1. The media specification other than above are unchanged.
2. When marking black marks on label rolls, the following requirements must be satisfied.
When the gap length is less than 4 mm:
The black mark length should be longer than the gap length.
When the gap length is 4 mm or more:
The black mark should not overlap the gap for more than 4 mm and the following label.
3. When the print speed is 8"/sec., the width including backing paper will be 84 to 150 mm. When the optional cutter
module or strip module is used, the width including backing paper will be 101.6 to 175 mm.
4. If the label used is smaller than specified, the print head life may be shortened.
5. When issuing thermal labels at 8"/sec., the print stop position should be set to a minimum of 1 mm inside the label.

2.4 RIBBON

Type
Width
Length
Outer diameter
Mantenimiento Periféricos Informáticos C/Canteras,15 28860 Paracuellos de Jarama Madrid Tel: 91 748 16 04 www.mpi.com.es
Label
I
J
Reference
coordinate
1
H
Reference
coordinate
2
G
D
C
Label dispensing mode
B-672
B-682
B-672
B-682
B-672
Standard
B-682
Label
B-672
Max. memory
B-672
Standard
B-682
Tag
B-672
Max. memory
B-672
Standard
B-682
B-672
Max. memory
Label
Tag
NOTES:
1. "On the fly issue" means that the printer can draw and print without stopping
between labels.
Spool type
2. To ensure print quality and print head life use only TOSHIBA TEC specified media
115 mm ~ 185 mm
and ribbons.
3. When using the cutter ensure that label length B plus inter label gap length E
(See NOTE 5.)
exceeds 35 mm. (i.e. label pitch should be greater than 35 mm.)
300 m
4. To avoid ribbon wrinkles use the ribbon which is wider than media by 5mm or more.
However, too much difference in width between the two may cause wrinkles.
Ø72 mm (max.)
5. When the print speed is 8"/sec., the width will be 115 to 160 mm.
Refer to the following
NOTE 2.
Black Mark
(on reverse side)
I
Stop
position
E
Cut
position
A
H
B
Feed direction
Fig. 2-1
Batch mode Strip mode
10.00 ~ 999.0 25.4 ~ 999.0
10.00 ~ 1709.0 25.4 ~ 1709.0
7.5 ~ 996.5 22.9 ~ 996.5
7.5 ~ 1707.0 22.9 ~ 1707.0
84.0 ~ 175.0 (See NOTE 3.)
81.0 ~ 172.0
2.5 ~ 20.0 2.5 ~ 20.0
2.5 ~ 10.0
10.0 ~ 170.6
5.5 ~ 298.6 20.9 ~ 298.6
5.5 ~ 1705.0 20.9 ~ 1705.0
5.5 ~ 981.3 20.9 ~ 981.3
8.0 ~ 298.6 23.4 ~ 298.6
8.0 ~ 1705.0
8.0 ~ 981.3 23.4 ~ 981.3
Refer to the following NOTE 2.
Ø200 Max.
0.13 ~ 0.17
0.10 ~ 0.17
E2-3
ENGLISH VERSION EO1-33016
Tag paper Black Mark
(on reverse side)
Tag paper
F
Reference
coordinate
1
A
Reference
coordinate
2
G
C
[Unit: mm]
Cut mode
Label: 38 ~ 999.0
Tag: 25.4 ~ 999.0
Label: 38 ~ 1709.0
Tag: 25.4 ~ 1709.0
25.0 ~ 993.0
25.0 ~ 1703.0
6.0 ~ 20.0
23.0 ~ 298.6
23.0 ~ 1705.0
23.0 ~ 981.3
23.4 ~ 298.6
23.4 ~ 1705.0
23.4 ~ 981.3
1.0
149.3
852.0
490.6
2.3 MEDIA