Bosch GLM Professional 80+R60 Manual Original página 20

OBJ_BUCH-1347-008.book Page 20 Monday, December 21, 2015 3:09 PM
20 | English
Digital Laser Measure
Laser type
Laser beam diameter (at 25 °C) approx.
– at 10 m distance
– at 80 m distance
Setting accuracy of the laser to the housing, approx.
– Vertical
– Horizontal
Automatic switch-off after approx.
– Laser
– Measuring tool (without measurement)
Weight according to EPTA-Procedure 01:2014
Dimensions
Degree of protection
Measuring rail
Article number
Dimensions
Battery
Rated voltage
Capacity
Number of battery cells
Single measurements per battery charge, approx.
Battery Charger
Article number
Charging time
Output voltage
Charging current
Protection class
A) For measurements from the rear measuring-tool edge, 100 % reflectance of the target (e.g., a white-painted wall), weak backlight and 25 °C oper-
ating temperature. Additionally, a deviation influence of ±0.05 mm/m must be taken into account.
B) For measurements from the rear measuring-tool edge, 10 – 100 % reflectance of the target, strong backlight and – 10 °C to +50 °C operating tem-
perature. Additionally, a deviation influence of ±0.29 mm/m must be taken into account.
C) For measurements with the rear side of the unit as reference, the max. measuring range is ±60°
D) After calibration at 0 ° and 90 ° with an additional grade error of ±0.01 °/degree to 45 ° (max.).
E) In the continuous measurement function, the maximum operating temperature is +40 °C.
F) The width of the laser line depends on the surface characteristics and on the ambient conditions.
G) at 25 °C
H) For a new and charged battery without display illumination and tone signal.
Please observe the article number on the type plate of your battery charger. The trade names of individual battery chargers may vary.
The measuring tool can be clearly identified with the serial number 18 on the type plate.
Product Features
The numbering of the product features shown refers to the il-
lustration of the measuring tool on the graphic page.
1 Display
2 Measuring button
3 Button for grade measurement / calibration **
4 Button for function mode / basic settings **
5 Minus button
6 Button for result / timer function **
1 609 92A 1YP | (21.12.15)
GLM 80
635 nm, <1 mW
F)
6 mm
F)
48 mm
G)
±2 mm/m
G)
±10 mm/m
20 s
5 min
0.14 kg
51 x 111 x 30 mm
IP 54 (dust and splash water IP 54 (dust and splash water
protected)
–
–
Li-Ion
3.7 V
1.25 Ah
1
H)
25000
2 609 120 4..
approx.3 h
5.0 V
500 mA
/II
7 Button for measured-value list / storage of constant **
8 Button for clearing the internal memory / On/Off **
9 Positioning pin
10 Button for selection of the reference level
11 Plus button
12 Button for length, area and volume measurement
13 Charge socket cover
14 Socket for charge connector
15 Fixture for carrying strap
GLM 80+R60
635 nm, <1 mW
F)
6 mm
F)
48 mm
G)
±2 mm/m
G)
±10 mm/m
20 s
5 min
0.14 kg
51 x 111 x 30 mm
protected)
3 601 K79 000
58 x 610 x 30 mm
Li-Ion
3.7 V
1.25 Ah
1
H)
25000
2 609 120 4..
approx.3 h
5.0 V
500 mA
/II
Bosch Power Tools