Idiomas disponibles
Idiomas disponibles
• Red light of the diode - (after connecting the battery to the charger)
indicates that the battery charging process is in progress.
• Green light on again - means that the battery is fully charged.
After charging the battery, the LED (11) will turn green until the charger is
disconnected from the mains.
Batteries become very hot during the charging process. Do not start
work immediately after charging - wait until the battery reaches
temperature
SPINDLE BRAKE
Drill is equipped with electronic brake that stops the spindle immediately
after the switch button (8) is released. The brake ensures precision when
screwing or drilling and prevents free spindle rotation after switching off.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
Switching on – press the switch button (8).
Switching off – release the switch button (8).
Each time the switch button (8) is pressed, the LED diode (9) lights up to
illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (8) to adjust rotational
speed while operating. Speed control allows for soft start, which provides
working control during tightening and undoing bolts.
CIRCUMFERENTIAL IMPACT ACTION
The tool rotates the spindle when tightening, and creates circumferential
impact. Impact action actuates automatically when the load increases.
Then a high peak torque is applied. Keep watching the screw or bolt for full
control over tightening. Keep control over tightening force by adjusting
rotational speed.
WORKING TOOL INSTALLATION
Pull away the fixing sleeve of the tool chuck (2) (fig. C) against the
spring force.
Insert working tool shank into the tool chuck (1) and slide it in to
mechanical stop (it may be necessary to turn the working tool so it can
reach appropriate position).
Release the fixing sleeve of the tool chuck (2), it will finally lock the
working tool. The fixing sleeve of the tool chuck (2) will return to its
position (fig. D).
Deinstallation of the tool is similar to installation, only the sequence of
actions is reversed.
Use additional driver bit adapter with short driver bits.
RIGHT-LEFT DIRECTION OF ROTATION
Choose direction of spindle rotation with the direction selector switch (4)
(fig. E).
Clockwise rotation – set the switch (4) to the extreme left position.
Counter-clockwise rotation – set the switch (4) to the extreme right
position.
* In certain cases position of the switch related to rotation may be different than specified.
Please refer to graphic signs located on the switch or tool body.
Safe position of the direction selector switch (4) is in the middle, it prevents
accidental starting of the power tool.
When the switch is in this position, the power tool cannot be started.
Use this position of the switch to change bits.
Before starting the tool make sure the position of the direction selector
switch (4) is correct.
Do not change direction of rotation when the spindle of the power
tool is rotating.
Long lasting operation at low rotational speed of the spindle may
cause motor overheating. Long lasting drilling at low rotational
speed of the spindle may cause motor overheating.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
Cleaning the device after each use is recommended.
Do not use water or any other liquid for cleaning.
Clean the power tool, battery and charger with a dry cloth or blow
through with compressed air at low pressure.
Do not use any cleaning agents or solvents, they may damage
plastic parts.
Clean ventilation holes in the motor casing regularly to prevent
device overheating.
In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
Store the power tool and its equipment in a dry place, beyond
reach of children.
Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless impact driver
Parameter
Battery voltage
Max. torque
No-load speed range
Impact frequency range
Tool chuck
Protection class
Weight
Year of production
50G292 means both the type and designation of the machine
Parametr
Supply voltage
Power frequency
Maximum power
Charging voltage
Charging current
Ambient temperature range
Time of failure K113444
Protection class
Mass
Year of production
Parametr
Battery voltage
Battery type
Battery capicity
Amblent temperaturę range
Charging time for charger K113446
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure level
Sound power level
Vibration acceleration
Information regarding noise and vibration
The level of noise emitted by the device is described by: the level of the
emitted sound pressure LpA and the sound power level LwA (where K is
the measurement uncertainty). The vibrations emitted by the device are
described by the value of the vibration acceleration ah (where K is the
measurement uncertainty).
The following information: emitted sound pressure level LpA, sound power
level LwA and vibration acceleration ah have been measured in
accordance with EN 62841-2-2. The stated vibration level ah can be used
for the comparison of devices and for the initial assessment of vibration
exposure.
The stated vibration level is representative only for the basic use of the
device. If the machine is used for different applications or with different
work tools, the vibration level may change. The higher vibration level will
be influenced by inadequate or too rare maintenance. The reasons given
above may result in an increased exposure to vibration during the entire
period of operation.
To accurately estimate exposure to vibration, consider periods when
the equipment is turned off or when it is turned on but not in use.
After all factors have been carefully assessed, the overall vibration
exposure may be significantly lower.
In order to protect the user from the effects of vibrations, additional safety
measures should be implemented, such as: periodic maintenance of the
device and working tools, protection of the appropriate temperature of
hands and proper organization of work.
ENVIRONMENT PROTECTION
Electrical equipment must not be disposed off with household waste and,
instead, should be utilized at appropriate facilities. Information on
utilization can be provided by the product vendor or the local authorities.
Waste electrical and electronic equipment contains substances that are
not neutral to the natural environment. Equipment that is not recycled
constitutes a potential hazard to the environment and to human health.
Do not dispose the batteries with household wastes, do not throw in fire
or water. Damaged or worn out batteries should be properly recycled in
accordance with applicable directive for battery disposal.. Batteries
should be returned to collection points fully discharged, if the batteries are
not completely discharged, they must be protected against short circuits.
Used batteries can be returned free of charge at commercial locations.
Li-Ion
The buyer of the goods is obliged to return the used batteries.
* Right to introduce changes is reserved.
7
20V DC
120 Nm
0-2000 min
0-3000 min
6,35 mm (¼ '')
III
1,1 kg
2022
Charger K113445
230 V AC
21 V DC
2300 mA
5
0
C – 30
60 min
0,300 kg
Battery K113444
20 V DC
Li-Ion
1500 mAh
4
0
C – 40
1 h
0,4 kg
2022
LpA= 95,2 dB(A) K= 5 dB(A)
LwA= 106,2 dB(A) K= 5 dB(A)
ah= 11,322 m/s2 K= 1,5 m/s2
Value
-1
-1
Value
50 Hz
65 W
0
C
II
2022
Value
0
C
