Idiomas disponibles
Idiomas disponibles
ENGLISH
10. Tips and Tricks
•
Keep surfaces of the saw table
clean – in particular, remove resin
residue with a suitable cleaning and
maintenance spray (optional acces-
sory).
•
Afterwards, apply a light coat of slid-
ing compound (e.g. Waxilit).
11. Available Accessories
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A
Workstand
for an optimal working height. Pow-
der-coated sheet-metal construc-
tion.
B
Bandsaw Blade
induction-hardened teeth,
2240 x 12 x 0.5 A6,
general purpose blade for wood.
C
Bandsaw Blade
induction-hardened teeth,
2240 x 6 x 0.5 A4,
for contour cutting in wood.
D
Bandsaw Blade
induction-hardened teeth,
2240 x 15 x 0.5 A6,
for straight cuts in wood.
E
Bandsaw Blade
induction-hardened teeth,
2240 x 15 x 0.5 A2,
for non-ferrous metals.
F
Belt Sanding Attachment
for dressing cut surfaces.
G
Sanding Belt
No. 80 grit, 2240 x 20 (pack of 3)
H
Sanding Belt
No. 120 grit, 2240 x 20 (pack of 3)
I
Circle Cutting Attachment
for cutting circles of 120 to 260 mm
diameter. Best performance when
used with the contour cutting blade.
J
Mitre Fence
for accurate mitre cuts.
K
Precision 3-roller Guide
ensures
perfect
guiding
extended service life of the band-
saw blade. Adjusts without tools.
L
Dust Collection Adapter for Ø 100
mm port.
M
Dust Collector
helps to protect your health and to
keep the shop clean.
N
WAXILIT Sliding Compound
improves workpiece sliding on the
saw table.
O
Care and Maintenance Spray
to remove resin residue and pre-
serve metal surfaces.
24
12. Repairs
Danger!
Repairs to power tools must be
carried out by qualified electricians
only!
Power tools in need of repair can be sent
to the service centre of your country.
Refer to the spare parts list for the
address.
Please attach a description of the fault to
the power tool.
13. Environmental Protection
The saw's packaging can be 100 %
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
14. Trouble Shooting
Danger!
Before carrying out any fault
service or maintenance work always:
− switch machine OFF
− unplug power cable
− wait until the bandsaw blade has
come to a complete stop.
Check to see that all safety devices
are operational after each fault serv-
ice.
Motor does not run
Undervoltage relay tripped by power fail-
ure.
− Switch on again.
No mains voltage
− Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by blunt band-
saw blade or chip build-up in the hous-
ing:
− remove cause, let cool down for a
and
while then switch on again.
Motor and bandsaw blade running in
reverse
Incorrect phase sequence (models with
3-phase motor only):
− turn phase changer in the machine's
plug (see "Initial Operation").
Bandsaw blade is coasting (≥ 10 s)
Electronic motorbrake faulty:
− have On/Off switch replaced by a
qualified electrician.
Bandsaw blade wanders off the line
of cut or runs off the bandsaw wheels
Bandsaw blade is not running dead cen-
tre on the bandsaw wheels:
− Correct tracking (see "Care and
Maintenance").
Bandsaw blade breaks
Incorrect tension:
− correct bandsaw blade tension (see
"Initial Operation").
Load too high:
reduce pressure against bandsaw blade
(reduced feed speed).
Incorrect bandsaw blade:
− replace bandsaw blade (see "Care
and Maintenance"):
thin stock =
narrow bandsaw blade,
thick stock =
wide bandsaw blade.
Bandsaw blade warped
Load too high:
− avoid lateral pressure on the band-
saw blade.
Saw vibrates
Insufficient mounting:
− Fasten saw properly to a suitable
surface (see "initial operation").
Saw table loose:
− Align and fasten saw table.
Motor mount loose:
− Check fastening screws, tighten if
necessary.
Dust extraction port blocked
No dust collector connected or suction
capacity insufficient:
− Connect a dust collector or increase
suction capacity (air speed ≥ 20 m/
sec at dust extraction port).
