Idiomas disponibles
Idiomas disponibles
USING YOUR DYSON APPLIANCE
PLEASE READ THE 'iMPORTANT
SAFETY
iNSTRUCTIONS'
iN THIS
DYSON
OPERATING
MANUAL
BEFORE
PROCEEDING.
ASSEMBLY
Lie the appliance
on its back.
Attach
the cleaner
head by sliding
it on to the connections
on the lower front
part of the ball.
Ensure the electrical
plug
on the cleaner
head fits into the
twin-block
connection
on the body of the appliance,
which
is directly
above
the
airway.
Push firmly:
the cleaner
head will click
into place.
Stand the appliance
up straight.
Attach
the wand
handle
by sliding
it on to the top of the appliance.
The spring
clip in the handle
will click
into place.
Ensure the hose is straight.
Press the button
on the hose. Slide the wand
into the
hose.
Ensure the hose and wand
sit in the recess of the handle.
Slide the end of the
wand
down
into the handle
to secure
it
Close the wand
cap.
Slide the tool
holder
onto
the side of the duct as shown.
Ensure the cyclone
and
clear bin unit is secured
to the main body
of the
appliance.
Attach
the tools
as shown.
In use, the tools
can be attached
to either
the hose or
the wand.
Wind
the cord counter-clockwise
around
the cord
hooks.
Secure with the clip.
To watch
a short online
video
visit:
www.dyson.com/DC40getfingstarted
OPERATION
Unwind
the cord.
Plug the appliance
into the main
electricity
supply.
To switch
'ON'
or 'OFF'
press the power
button,
located
as shown.
Ta use, recline
the handle.
The stabilizer
stand
will automatically
lift up.
After
use, return
the appliance
to the upright
position,
pushing
it firmly
into
place.
The stabilizer
wheels
will automatically
lower.
Then
unplug
the appliance,
coil the cable
safely
and put the appliance
away.
Switch
'OFF'
the appliance,
unplug
and ensure
it is upright
before:
- changing
or using tools
- removing
the hose or airway
inspection
parts.
Use the cyclone
carry
handle
to carry
the appliance.
ATTAC H ME NTS
To release
the wand,
open the wand
cap and pull the red tube
up and away
from
the handle
until
it clicks into place.
Should
you wish to use the hose without
the wand,
follow
the above
instruction
and press the red button
to release
the wand
from the hose.
CARPETS OR HARD FLOORS
The brush
bar will always
default
to 'ON'
(spinning)
each tirne you switch the
appliance
'ON'
and recline
it far cleaning.
The brush
bar will not rotate when
the appliance
is upright.
Ta switch
the brush
bar 'OFF'
(e.g. far delicate
rugs and
hard floors):
- switch
the appliance
'ON'
- recline
the appliance
- press the brush
bar'ON/OFF'
button-
the brush
bar will stop
spinning.
The brush
bar will automatically
stop if it becomes
obstructed.
See 'Brush
bar -
clearing
obstructions'.
Before
vacuuming
your
flooring,
rugs and carpets,
check the manufacturer's
recommended
cleaning
instructions.
Some carpets
may fuzz if a rotating
brush
bar is used when
vacuuming.
If this
happens,
we recommend
vacuuming
in 'hard
floor'
made
and
consulting
with
the flooring
manufacturer.
The brush
bar on the appliance
may damage
some carpet
types.
If you are
unsure,
turn 'OFF'
the brush
bar.
LOOKING AFTER YOUR DYSON APPLIANCE
Da not carry
out any maintenance
ar repair
work
other
than
that
shown
in this
Dysan
Operating
Manual,
ar advised
by the Dysan
Helpline.
Only
use parts
recommended
by Dysan.
If you da nat this could
invalidate
your
warranty.
Store the appliance
indoors.
Da nat use ar store
it below
32°F
(0°C).
Ensure the
appliance
is at room
temperature
before
operating.
Clean
the appliance
only with a dry cloth.
Da not use any lubricants,
cleaning
agents,
polishes
ar air fresheners
an any part
af the appliance.
If used in a garage,
always
wipe the base plate,
ball and
stabilizer
wheels
with
a dry cloth
after
vacuuming
to clean
off any sand,
dirt or pebbles
that could
damage
delicate
floors.
z_
VACUUMING
CAUTION:
Da nat use without
the clear
bin and filters
in place.
Fine dust such as plaster
dust ar flour
should
only be vacuumed
in very small
amounts.
Do not use the appliance
to pick up sharp
hard
objects,
small
toys,
pins,
paper
clips,
etc. They may damage
the appliance.
When
vacuuming,
certain
carpets
may generate
small
static
charges
in the clear
bin or wand.
These are harmless
and are nat associated
with the main electricity
supply.
Ta minimize
any effect
from
this, do not put your
hand ar insert
any
object
into the clear
bin unless you have first emptied
it and
rinsed
it out with
cold water
(see
'Cleaning
the clear
bin').
Powerful
suction
can cause the hose ta 'pull
back'
- please
take care.
Do nat work
with the appliance
above
you on the stairs.
Do nat put the appliance
on chairs,
tables,
etc.
Before
vacuuming
highly
polished
floors,
such as wood
ar linoleum,
first check
that the underside
of the floor
tool and its brushes
are free from
foreign
objects
that could
cause
marking.
Da nat leave the cleaner
head in one place
an delicate
floors.
Do nat use this vacuum
cleaner
outdoors.
The Dyson
Car Cleaning
Kit
(Model
08909)
is intended
far
use only
inside
a garage.
EMPTYING THE CLEAR BIN
Switch
'OFF'
and unplug
before
emptying
the clear bin.
Empty
as soon as the dirt reaches
the level of the MAX mark-
da not overfill.
To remove
the cyclone
and clear bin unit,
press down
on the red button
at the
rear of the carrying
handle
on the cyclone.
To release
the dirt,
press all the way down
on the red button
at the rear of the
carrying
handle
an the cyclone.
To minimize
dust/allergen
contact
when
emptying,
encase
the clear bin tightly
in
a plastic
bag
and empty.
Remove
the clear bin carefully.
Seal the bag tightly,
dispose
as normal.
To refit:
- close the clear
bin base so it clicks
into place
- push the cyclone
and
clear bin unit into the main body of the appliance;
it will
click into place
- ensure
the cyclone
and clear
bin unit is secure.
CLEANING THE CLEAR BIN
Remove
the cyclone
and clear
bin (instructions
above).
To separate
the cyclone
unit from
the clear bin press the red button
ta open
the clear bin base.
This exposes
a small
silver
button
behind
the red opening
mechanism.
Press the silver
button
and
separate
the cyclone
unit from
the
clear bin.
Clean
the clear
bin with cold water
only.
Ensure the clear bin is completely
dry before
replacing.
Do not use detergents,
polishes
or air fresheners
to clean the clear
bin.
Do nat put the clear bin in a dishwasher.
Do not immerse
the whole
cyclone
unit in water
or pour water
into the cyclones.
Clean
the cyclone
shroud
with a dry cloth or dry brush
to remove
lint and dust.
To refit:
- fit the cyclone
shroud
into the clear bin so that the silver
button
clicks and
engages
- close the clear
bin base so it clicks
into place
- push the cyclone
and
clear bin unit into the main body of the appliance;
it will click into place
- ensure
the cyclone
and clear
bin unit is secure.
WASHING YOUR FILTERS
Your appliance
has two washable
filters,
located
as shown.
Check
and wash
the filters
regularly
according
to instructions
to maintain
performance.
Switch
'OFF'
and unplug
before
checking
or removing
the filters.
The filters
may
require
more
frequent
washing
if vacuuming
fine dust.
Wash with cold water
only.
Do nat use detergents.
Do not put the filters
in a dishwasher,
washing
machine,
tumble
dryer,
oven,
microwave
Or
near an open flame.
To remove
filter
A see the 'Wash
filters'
section
in this Dyson
Operating
Manual.
After
washing
lay filter
A on its side and
leave at least 24 hours to dry
completely
before
refitting.
To remove
filter
B:
-turn
the central
locking
dial on the outer
cover
of the boll counter-clockwise
until the cover
is released
- lift off the cover
- turn the filter
one-quarter
counter-clockwise
to release.
Filter
B should
be rinsed
and tapped
out until the water
runs
clean,
then topped
out again
to ensure
all excess water
is removed.
Leave to dry completely
for
24 hours.
It is normal
for the filter
in the ball to turn
grey
in color.
To refit filter
B:
- refit the filter
on to the ball
- secure the filter
by turning
it one-quarter
turn
clockwise.
When
refitting
the outer
cover
of the ball,
keep turning
the central
locking
dial
clockwise.
When
it starts ta click it is locked.
To watch
a short
online
video
visit:
www.dyson.com/DC4Ofilterwash
