Used Symbols; Information On Intellectual Property; Dremel Remote And Mobile Services; Functional Description And Specifications - Dremel 3D45 Traducción De Las Instrucciones Originales

USED SYMBOLS

Symbol Name
Safety alert
symbol
Read manual
symbol
Danger symbol
DANGER
!
Warning symbol
WARNING
!
Caution symbol
!
Hot surface
hazard symbol.
UL US symbol
THIS IS A CLASS A PRODUCT. IN
WARNING
!
A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN
WHICH CASE THE USER MAY BE REQUIRED TO
TAKE ADEQUATE MEASURES.
INFORMATION ON INTELLECTUAL
PROPERTY
The Dremel 3D45 is intended for 3D printing objects
from digital files that you create or own, or have the
right to print using the Dremel 3D45. When making
objects using the Dremel 3D45, it is your responsibility
to ensure that you do not infringe any third party
intellectual property rights or violate any applicable
laws or regulations, such as U.S. or foreign intellectual
property laws. The Dremel 3D45 may not be used to
make objects protected by intellectual property rights
owned by third parties without such third parties'
permission. Using the Dremel 3D45 to do any of the
following may require the permission of third parties:
to make a duplicate or facsimile (in whole or in part) of
any object not created by you, to make an object from
a digital file you do not own, or to make an object from
a scan of a physical object that you did not create. It is
your responsibility to obtain such permission. In some
cases, you may not be able to obtain such permission.
Designation/
Explanation
It is used to alert you
to potential personal
injury hazards. Obey
all safety messages
that follow this symbol
to avoid possible
injury or death.
Alerts user to read
manual
indicates a hazardous
situation which, if not
avoided, will result in
death or serious injury
indicates a hazardous
situation which, if not
avoided, could result
in death or serious
injury.
indicates a hazardous
situation which, if not
avoided, will result
in minor or moderate
injury.
Contact may cause
burn. Allow to cool
before servicing.
This symbol
designates that
this tool is listed
by Underwriters
Laboratories, to
United States and
Canadian Standards.
Where such permission cannot be obtained, you
should not 3D print such object, or you do so at your
own risk. You may not modify, reverse engineer,
decompile, or disassemble the Dremel 3D45 or its
software or firmware, except as permitted by applicable
law. If you use the Dremel 3D45 in any way other than
as recommended and described in these Operating/
Safety Instructions, you do so at your own risk. Using
the Dremel 3D45 to make objects that infringe any
intellectual property rights owned by third parties could
result in civil or criminal prosecution and penalties,
and you could be liable for money damages, fines, or
imprisonment.
DREMEL REMOTE AND MOBILE
Dremel remote and mobile services provide you with
information and services regarding your Dremel 3D
products. The type of information provided by Dremel
remote and mobile services may change from time to
time. All product information and services are provided
for your convenience, "As is" and "As Available".
NOTE: The availability of Remote and Mobile Services
may depend on your region.
Dremel does not guarantee that the information or
services will be available, accurate, or reliable, or that
product information or services will provide safety in
your home. You use all product information, services,
and products at your discretion and risk. The product
information and services are not intended as a
substitute for direct means of obtaining information.
Network connectivity requires an access point and high
speed internet connection. Internet service provider
charges may apply.
Mobile printing requires a compatible mobile device
and data plan. Carrier charges may apply.
FUNCTIONAL DESCRIPTION AND
SPECIFICATIONS
Extruder: Single extrusion
Extruder temperature: Up to 280°C (536°F)
Build Platform Temperature: Up to 100°C (212°F)
Operating Interface: 4.5" full color IPS touch screen
Maximum Build Volume: 10" x 6" x 6.7" (255mm x
155mm x 170mm)
Layer Thickness: 50 microns | 0.05 mm
Filament types and colors: See dremel3d.com
Internal Storage: 8GB
External Storage: USB Flash Drive
WEIGHT & DIMENSIONS
Weight (without spool): 19.4kg (42.8lbs)
Dimensions: 20.25" x 16" x 15.9" (515mm x 406mm x
394mm)
ONLY works with Dremel 1.75mm filament
4
SERVICES
BUILDING
FILAMENT