DeWalt DCPS620 Manual De Instrucciones página 10

English
chain 14 against limb. Hold pole saw firmly in place to
avoid possible bouncing or skating (sideways movement)
of pole saw.
b. Guide pole saw using light pressure. Make first cut 6"
(152 mm) from tree trunk on underside of limb. Use top of
guide bar 13 to make this cut. Cut 1/3 through diameter of
limb. Then make the finish cut from the top. If you try to cut
off thick branches from the bottom, the branch may close in
and pinch the saw chain in the cut. If you try to cut off thick
branches from the top, without a shallow undercut, the
branch may splinter. Do not force pole saw. The motor will
overload and can burn out. It will do the job better and safer
at the rate for which it was intended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch
sure saw chain has stopped before setting pole saw down.
Saw Chain Sharpness

CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut you
when it is not running.
iMPORTAnT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest D
service center.
nOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should
be used. It is recommended that a saw chain be sharpened
no more than four times.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Regular maintenance ensures a long effective life for the
tool. After every 10 minutes of use be sure to remove
the battery (be aware the chain and bar can be hot!) and
check the bar and chain for correct tension and lubricate
per Adjusting Chain Tension and Saw Chain and Guide
Bar Oiling.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These chemicals
may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should
e
be used with this product.
Replacement chain and bar are available from your
nearest D WALT service center.
e
10
• DCPS620 requires replacement chain service part number
DWO1DT608. Replacement 8" (203 mm) bar, service part
number DWZCSB8.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
. Make
4
inspection and replacement, when applicable) should
be performed by a D
D WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
WALT
• COnFiRMATiOn OF OWnERshiP: In case of an
e
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account‑login.
Three‑Year Limited Warranty
For warranty terms, go to www.dewalt.com/support/
warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WALT (1-800-433-9258) or visit our website:
e
WALT factory service center or a
e
WALT Industrial Tool Co., 701 East
e
WALT Industrial
e
WALT
e
WALT
e