fadini Junior 633 Manual De Instrucciones página 34

Junior 633 - Junior 650
NL
GENERAL WARNINGS FOR PEOPLE SAFETY
INTRODUCTION
This operator is designed for a specific scope of applications as
indicated in this manual, including safety, control and signaling
accessories as minimum required with FADINI equipment.
applications not explicitly included in this manual may cause operation
problems or damages to properties and people.
not liable for damages caused by the incorrect use of the equipment, or
for applications not included in this manual or for malfunctioning
resulting from the use of materials or accessories not recommended by
the manufacturer. The manufacturer reserves the right to make
changes to its products without prior notice.
indicated in this manual is to be considered not allowed.
BEFORE INSTALLATION
Before commencing operator installation assess the suitability of the
access, its general condition and the structure.
is no risk of impact, crushing, shearing, conveying, cutting, entangling
and lifting situations, which may prejudice people safety. Do not install
near any source of heat and avoid contacts with flammable substances.
Keep all the accessories able to turn on the operator (transmitters,
proximity readers, key-switches, etc) out of the reach of the children.
Transit trough the access only with stationary operator.
children and/or people to stand in the proximity of a working operator.
To ensure safety in the whole movement area of a gate it is advisable to
install photocells, sensitive edges, magnetic loops and detectors. Use
yellow-black strips or proper signals to identify dangerous spots.
Before cleaning and maintenance operations, disconnect the appliance
from the mains by switching off the master switch.
actuator, do not cut the electric wires, but disconnect them from the
terminal box by loosening the screws inside the junction box.
INSTALLATION
All installation operations must be performed by a qualified technician,
in observance of the Machinery Directive 2006/42/CE and safety
regulations EN 12453 - EN 12445.
thermal-magnetic circuit breaker 0,03 A - 230 V - 50 Hz upstream the
installation. Use appropriate objects to test the correct functionality of
the safety accessories, such as photocells, sensitive edges, etc. Carry
out a risk analysis by means of appropriate instruments measuring the
crushing and impact force of the main opening and closing edge in
compliance with EN 12445. Identify the appropriate solution necessary
to eliminate and reduce such risks.
automate is equipped with a pedestrian entrance, it is appropriate to
prepare the system in such a way to prohibit the operation of the engine
when the pedestrian entrance is used.
CE marking on the gate warning about the presence of an automated
installation. The installer must inform and instruct the end user about
the proper use of the system by releasing him a technical dossier,
including: layout and components of the installation, risk analysis,
verification of safety accessories, verification of impact forces and
reporting of residual risks.
Any
Meccanica Fadini is
All that is not explicitly
Make sure that there
Do not allow
If removing the
Verify the presence of a
In case where the gate to
Apply safety nameplates with
INFORMATION FOR END-USERS
The end-user is required to read carefully and to receive information
concerning only the operation of the installation so that he becomes
himself responsible for the correct use of it.
establish a written maintenance contract with the installer/maintenance
technician (on -call). Any maintenance operation must be done by
qualified technicians. Keep this instruction carefully.
WARNINGS FOR THE CORRECT OPERATION OF THE INSTALLATION
For optimum performance of system over time according to safety
regulations, it is necessary to perform proper maintenance and
monitoring of the entire installation: the automation, the electronic
equipment and the cables connected to these.
The entire installation must be carried out by qualified technical
personnel, filling in the Maintenance Manual indicated in the Safety
Regulation Book (to be requested or downloaded from the site
www.fadini.net/supporto/downloads).
inspection at least every 6 months, while for the electronic equipment
and safety systems an inspection at least once every month is required.
The manufacturer, Meccanica Fadini snc, is not responsible for
non-observance of good
maintenance of the installation.
DISPOSAL OF MATERIAL
Dispose properly of the packaging materials such as cardboard, nylon,
polystyrene etc. through specializing companies (after verification of the
regulations in force at the place of installation in the field of waste
disposal). Disposal of electrical and electronic materials: to remove and
dispose through specializing companies, as per Directive 2003/108/CE.
Disposal of substances hazardous for the environment is prohibited.
34
The end-user shall
Operator: maintenance
installation practice and incorrect