Teleco TVRCM868A03BLE Manual De Instrucciones página 2

(EN) PRODUCT DESCRIPTION
Superheterodyne radio control devices, with the carrier frequency in the UHF band controlled by quartz, for the remote control of electronic
and electrical appliances in conformity with the laws and standards in force. The transmitter code can be inserted (memorised) either directly
into the receiver. The user code is memorised under EEprom in the receiver which maintains the code information even when faced with
blackouts. The code transmission type is "Rolling-code".
It is also possible to control the device via BLUETOOTH using the APP.
1.0 - INSTALLATION & BLUETOOTH CONNECTION
Download the APP T-Pool from App Store o Google Play. Check the compatibility with your device first.
QR CODE IOS
After installation, you must choose a 4-digit numeric password and confirm it.
Connection: activate Bluetooth communication on your device and start the T-Pool APP.
Select Setup menu ► Installation, press "+", write the name of the new installation and enter the code shown on the
Receiver. Press "Connect" to make the connection. The receiver confirms the connection to the device with a 2 second beep.
The BLUETOOTH power signal can be set on 5 levels from a minimum value (operation near the receiver) to a
maximum value (remote operation from the receiver).
NOTE: The bluetooth power adjustment is intended to ensure that the coverage control is performed in view of
the pool. The Bluetooth adjustment can be performed at any time for security reasons.
2.0 - COUPLE CODE MEMORIZATION
Press the button P1 one time and hold down, the buzzer will sound continuously; press the channel which is to be memorized, the buzzer will
sound intermittently and rapidly.
COUPLE: *T1 and T3 execute an OPENING
*T2 and T4 execute a CLOSING
NOTE: in automatic functioning, the second pressure of the same button STOPS the movement.
2.1 - RADIO MEMORIZZATION AUX OUTPUT
Press 2 times the button P1 and hold down, the buzzer will sound intermittently slowly. press the channel which is to be memorized, the
buzzer will sound intermittently and rapidly.
COUPLE: *T1 and T3 execute ACTIVATION AUX
*T2 and T4 execute DEACTIVATION AUX
If the code is not memorised it could be due to the following conditions:
the code already exists in memory or the memory is full. In this case the buzzer will make 3 bip each time the power is switched ON. (The
maximum number of codes that can be memorized is 100).
2.2 - TO CANCEL A CODE WITH THE PUSH BUTTON DEL IN THE RECEIVER
Press 3 times the button P1 and hold down, the buzzer will sound intermittently slowly. Transmit the code to cancel, once it has been cancelled,
buzzer will sound continuously.
2.3 - TO CANCEL ALL MEMORISED CODES IN THE RECEIVER
Press 4 times the button P1 and hold it down for at least 10 seconds (during this period buzzer will sound intermittently and quickly) as buzzer
will sound continuously. Release the button after completing the operation.
3.0 - AUTOMATIC TIMED OUTPUTS OPERATION
Setting with a timed command through the combination of dipswitches 1 to 2 which varies the time from 60 sec. to a maximum of 240 sec.
60 sec. 120 sec. 180 sec. 240 sec.
DIP1
OFF ON
DIP2 OFF OFF
4.0 - ANTENNA
The correct installation and connection of the antenna is fundamental in order to obtain a good range for the installation. Connect a 8.5 cm
piece of wire to the antenna pole connection on the device. As an alternative (and for better results) use a tuned antenna connected to the
receiver via a coaxial cable RG 58 (impedance 50 Ω) with a maximum length of 15 metres (mod. ANT868).
5.0 - TECHNICAL SPECIFICATIONS
reception frequency
power supply
maximum power consumption at rest
maximum power consumption with activated relay
dropout delay
operating temperature range
maximum commutable power at the relay: voltage
load dc
load ac
Bluetooth 4.1(BLE) (max signal range 15mt, free field) 2,4 GHz
In the view of a constant development of their products, the manufacturer reserves the right for changing technical data and features without
prior notice.
QR CODE ANDROID
OFF ON
ON ON
868,3 MHz
12/24 VAc-Dc
10 mA
25 mA
1 s
-20° ÷ + 60°C
48 Vac
24 W
60 VA