Idiomas disponibles
Idiomas disponibles
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel. To use the equipment properly
you must also observe the safety regulations, the
assembly instructions and the operating instruc-
tions to be found in this manual.
All persons who use and service the equipment
have to be acquainted with this manual and must
be informed about the machine's potential ha-
zards.
It is also imperative to observe the accident pre-
vention regulations in force in your area.
The same applies for the general rules of health
and safety at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Harmful emissions of wood dust when used
in closed rooms.
•
Contact with the blade in the uncovered cut-
ting zone.
•
Injuries (cuts) when changing the blade.
•
Crushed fingers.
•
Kickback.
•
Tilting of the workpiece due to inadequate
support.
•
Touching the blade.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Anl_TH_SS_405_EL_SPK7.indb 19
Anl_TH_SS_405_EL_SPK7.indb 19
GB
4. Technical data
Mains voltage: ................................. 230 V ~ 50Hz
Power consumption: .................................... 80 W
Operating mode: ................................. S2 20 min
Power consumption: .................................. 120 W
Operating mode: .....................................S6 30%
Idle speed n
: ................................400-1600 min
0
Protection type: ........................................... IP 20
Stroke: ...................................................... 21 mm
Base area: ..................................... 450 x 280 mm
Tilting range of table: .............. 0° to 45° to the left
Table size: ................................... 413,5 x 253 mm
Saw blade length: ................................... 127 mm
Throat: .................................................... 406 mm
Max. cutting height at 90°: ......................... 57 mm
Max. cutting height at 45°: ........................ 27 mm
Weight: ........................................... approx. 13 kg
Load factor:
A load factor of S2 20 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (80 W) for
no longer than the time stipulated on the speci-
fi cations label (20 min). If you fail to observe this
time limit the motor will overheat. During the OFF
period the motor will cool again to its starting
temperature.
Operating mode S6 30%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 30% of the cycle at the
specifi ed rating and must then be allowed to idle
for 70% of the cycle.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
sound pressure level:
pA
L
sound power level:
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
- 19 -
-1
Operation Idle speed
80.2 dB
65.1 dB
88.4 dB
74.8 dB
18.04.13 13:19
18.04.13 13:19
