Idiomas disponibles
Idiomas disponibles
Establish the connection to the exhaust air open-
2.
ing.
Seal the joints appropriately.
3.
Aligning the appliance in the worktop cut-out
Use the enclosed spacers to adjust the circumfer-
1.
ential gap between the appliance and the worktop
to a uniform distance of 1.5 to 2 mm.
→ Fig.
43
Remove the spacers before sealing the join.
2.
Connecting the cables to the appliance
Connect one of the longer cables to the appliance
1.
and to any control knob.
→ Fig.
53
Ensure that the plugs snap into place in the sock-
2.
ets.
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
Observe the filters' air flow direction.
1.
Insert two of the filters into the left and right of the
2.
appliance, and slide them forwards.
→ Fig.
54
Insert the other filters into the left and right of the
3.
appliance.
→ Fig.
55
Inserting grease filters
Insert the grease filter.
▶
→ Fig.
56
Positioning the ventilation grille
Position the ventilation grille.
▶
→ Fig.
57
Establishing the connection to the power
supply
Observe the connection data on the rating plate.
1.
For 3 N, connect the cable to the mains socket in
2.
accordance with the figure.
→ Fig.
58
For 2 N, connect the cable to the mains socket in
3.
accordance with the figure.
→ Fig.
59
For 1 N, connect the cable to the mains socket in
4.
accordance with the figure.
→ Fig.
60
For 2 L/2 N, connect the cable to the mains
5.
socket in accordance with the figure.
→ Fig.
61
Note the colours of the cables.
6.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
If required, arrange the supplied wire end ferrules
7.
differently depending on the type of connection.
To connect two cables, if required, use a wire end
8.
ferrule.
Shorten the wires.
‒
Remove the insulation.
‒
Checking the function
Switch on the appliance.
1.
If
,
or
lights up, the appliance is not
2.
connected correctly. → "Checking and correcting
the electrical connection", Page 22
22
If no faults appear in the appliance's display, use
3.
the operating instructions to check that the ventila-
tion is working.
Checking and correcting the electrical connection
Disconnect the appliance from the power supply.
1.
Check whether the connection to the appliance
2.
and the building-side connection correspond to
the connection diagram in these installation in-
structions. → "Preparing the electrical connec-
tion", Page 18 → "Establishing the connection to
the power supply", Page 22
For 3 N, observe the following figure.
3.
→ Fig.
62
For 2 N, observe the following figure.
4.
→ Fig.
63
For 1 N, observe the following figure.
5.
→ Fig.
64
Sealing crevices
Requirement: You must carry out a function test be-
fore sealing the joint.
Seal the gap around it using suitable, heat-resist-
1.
ant silicone, e.g. Novasil® S70 or Ottoseal® S70.
→ Fig.
65
Unsuitable silicone adhesive causes permanent
discoloration to natural stone worktops.
Use the smoothing agent recommended by the
2.
manufacturer to smooth the crevice.
Observe the usage instructions for the silicone ad-
3.
hesive.
Leave the silicone adhesive to dry for at least 24
4.
hours.
The drying time depends on the ambient temper-
ature.
Do not operate the appliance until the silicone has
5.
dried completely.
Switching the display for air extraction
mode
If required for the air extraction mode and the air
1.
recirculation mode, change the display of the elec-
tronic control in the basic settings.
Observe the basic settings section in the instruc-
2.
tion manual.
Removing the appliance
ATTENTION!
Tools may damage the appliance frame.
Do not prise out the appliance from above.
▶
Disconnect the appliance from the power supply.
1.
Remove the exhaust air duct or undo the circulat-
2.
ing-air connections.
Remove the silicone joint.
3.
Push out the appliance from below.
4.
es
Volumen de suministro
Al desembalar el aparato, comprobar que estén to-
das las piezas y que no presenten daños ocasiona-
dos durante el transporte.
→ Fig.
1
Pedir el mando de control adecuado en negro o
acero inoxidable.
→ Fig.
2
