Virutex SC134L Manual De Instrucciones página 6

To turn the machine off, release button A (Fig. 1).
MODEL SC234L
To turn the machine on, keep button B pressed down (Fig.
2). For continuous action, lock button B into position
by means of button C (Fig. 2). To turn the machine off,
use button C to unlock button B.
5. INSERTING AND CHANGING THE
SAW BLADE (Fig. 3 to 10)
To insert the saw blade, transparent shield D must first
be removed (Fig. 3).
When the transparent shield has been removed, put fast-
fix mechanism E into the highest position and place saw
blade F into the slot of the fixing mechanism (Fig. 4).
Push the blade in until the teeth are held in place by
the fixing mechanism (Fig. 5).
Finally, put locking button E into its lowest position, so
that the blade is fixed and locked into place (Fig. 6).
Before beginning work, replace transparent shield D.
To remove the blade, transparent shield D must first be
removed (Fig. 8).
Put locking button E into its highest position and pull
down on saw blade F -(Fig. 9).
Locking button E will automatically return to its original
position.
Finally, replace transparent shield D -(Fig. 10).
The jig saw comes equipped with two
protective guards, as shown in (Figures
14 and 15).
The protective guard shown S (Fig. 14) is designed for
dust-free operation and should only be used when the
machine is hooked up to an external dust collector.
For cuts on an angle, use only the protective guard shown
T (Fig. 15), never the protective guard S (Fig. 14).
6. ADJUSTING THE PENDULAR MOVEMENT
Using the pendular movement enables you to achieve
maximum cutting efficiency. To select and start up the
pendular system, use lever G (Fig. 1-2). The recommen-
ded positions for each type of material are shown on
plate H (Fig. 1-2).
SC134L-SC234L jig saws allow you to select the different
pendular positions even when the machine is running.
7. ADJUSTING THE CUTTING SPEED
The cutting speed can be precision-controlled using
wheel I, from position A through to position G (Fig. 1
for SC134L and Fig. 2 for SC234L). This option means
that you can choose the best option for the material
you are cutting.
6
The recommended position for each type of material
is as follows:
MATERIAL
WOOD
STEEL
ALUMINIUM
RUBBER
CERAMICS
These positions are also shown on plate H (Fig. 1-2).
8. CUTTING WITHOUT PRIOR DRILLING (Fig. 11)
Place the front edge of the base of the machine onto
the piece to be cut and press down gently.
Move lever G (Fig. 11) from the variable position into
point O.
9. ADJUSTING THE BASE (Fig. 12)
Loosen screw K (Fig. 12) using the hexagonal key supplied
with the standard equipment. Pull back base J and adjust
it to the desired angle (0°, 15°, 30° or 45°), then return
the base to its original position and fix it in place once
again with screw K. Intermediate angles must be fixed
with the base pulled back.
10. ANTI-SPLINTER CUTTING GUIDE (Fig. 12)
Anti-splinter cutting guide L - (Fig. 12) may only be
used when the base is at 0°.
11. PRECAUTIONS TO BE TAKEN WHEN SAWING
When sawing metal, apply a lubricating and cooling
product to the jig saw blade. When cutting thin sheets
of metal, these should be fixed to a wooden support in
order to achieve a finer cut.
Before penetrating a wall or ceiling with the jig saw blade,
ensure that there are no electrical wires behind it.
Always hold the machine by the insulated parts.
12. CONNECTING TO A DUST COLLECTOR
The nozzle of machine M (Fig. 1-2) may be easily con-
nected to one of our dust collectors (VIRUTEX AS182K
and AS282K) by using the kit (References no. 6448073
our 1746245).
To release the nozzle, press down on fixing bolt N and
pull back the nozzle (Fig. 13).
13. MAINTAINING AND CHANGING THE
BRUSHES
Change the brushes before then reach a length of
5 mm. For model SC134L, loosen screws O and pull
out the back of housing P (Fig. 1). The brushes will be
clearly visible. Release the retaining spring, undo the
WHEEL POSITION
G
D-E
E
B-C
A-C