Idiomas disponibles
Idiomas disponibles
ENGLISH
2.Fm : The Receiver Has A Built-In Fm Wire Antenna Hanging At The Rear Cabinet. This Wire Should Be Totally Unraveled And Extended For
Best Reception.
Fm & Fm-Stereo Radio Encoding
1. Press Tuner Button To Activate "Tune" Mode And Select The Desired Band By Radio Band Button (Am Or Fm).
2. Insert Memory Device (Usb Drive, Sd Or Mmc Card)
3. Press The Rec Button, It Will Take 3-5 Seconds To Read Memory Device. Then Usb Or Sd Icon Will Be Flashing.
4. Pressing Skip Up Or Skip Down Button To Select Desired Mode (Usb Or Sd) For Encoding. Then Press The Rec Button Again To Confirm. And
The System Is Starting The Encoding Mode After Few Secondss.
5. If Only Usb Drive, Sd Or Mmc Card Is Inserted, Step 4 Can Be Skipped.
6. The Usb Or Sd Icon Will Be Flashing On The Display Durnig Encoding.
7. To Finish Encoding, Press Stop Button And Display Will Show "End" And Return To " Tuner" Mode.
Remark:-
-The Recording Speed Is 1:1 And According To The Actual Playing Time Of Fm Or Fm-St Radio
-The Recording Format Is Preset At – Mp3 Bit Rate : 128 Kbps
-During Fm & Fm-Stereo Radio Encoding, Radio Freqeuncy Is Fxied And Cannot Be Tuned
Phono & Encoding
Noted:
-Remove The Stylus Protector.
-Be Sure That The Tone Arm Is Being Detached From The Tone Arm Rest Before Operating And Re-Secured Again Afterwards.
1. Press Function Button To Select "Phon" On Display.
2. Set The Speed Selector To The Proper Position Depending On The Record To Be Played.
3. Place The Record On The Platter, Use The 45 Rpm Adaptor If Required.
4. Push The Lift Lever Upward To Raise The Tone Arm From The Arm Park, And Then Slowly Move It To The Record Side. The Platter Will Start To
Rotate.
5. Put Down The Lift Lever To Drop The Tone Arm And Touch The Record Gently. Phono Playing Starts Now.
6. Push The Lift Lever Upward To Raise The Tone Arm From The Arm Park, Now Platter Will Still Be Rotating But Phono Playing Will Stop. To Continue
The Playing, The User Needs To Put Down The Lift Lever.
7. Adjust The Volume To The Desired Level.
8. At The End Of Record, The Platter Will Automatically Stop Rotating. Push The Lift Lever Upward To Raise The Tone Arm And Move It To The Arm
Park, And Then Put Down The Lift Lever.
9. To Stop Manually, Lift The Tone Arm From The Record And Return It To The Arm Park.
Remark : As Some Kind Of Record The Auto-Stop Area Was Out Of The Unit Setting, So It Will Stop Before The Last Track Finishes. In This Case,
Select The Auto-Stop Switch To " Off " Position, Then It Will Run To The End Of The Record But Will Not Stop Automatically (Turn Off The Unit By
Power Button Or Switch Back The Auto-Stop Switch To " On " Position To Stop The Platter Rotate). Then Put Back The Tone Arm To The Arm Park.
Phono Encoding
1. Press Function Button Repeatedly To Activate "Phono" On Display And Then Insert Memory Device (Usb Drive, Sd Or Mmc Card).
2. Press The Rec Button, It Will Take 3-5 Seconds To Read Memory Device. Then Usb Or Sd Icon Will Be Flashing.
3. Pressing Skip Up Or Skip Down Button To Select Desired Mode (Usb Or Sd) For Encoding. Then Press The Rec Button Again To Confirm. And
The System Is Starting The Encoding Mode After Few Secondss.
4. If Only Usb Drive Or Sd/Mmc Card Is Inserted, Step 3 Can Be Skipped.
5. The Usb Or Sd Icon Will Be Flashing On The Display Durnig Encoding.
6. To Finish Encoding, Press Stop Button And Display Will Show "End" And Return To Phono Mode.
Remark:-
-The Recording Speed Is 1:1 And According To The Actual Plying Time Of The Phono
-The Recording Format Is Preset At – Mp3 Bit Rate : 128 Kbps
Aux In Jack & Encoding
Press Function Button Repeatedly To Activate "Aux" On Display, Then Connect The External Audio Device (Such As Cd Player) Through The Aux In
Jack. Audio Signal From The External Audio Device Can Be Played Through The System.
Aux In Encoding
1. Press Function Button To Select "Aux" On Display, Then Insert Memory Device (Usb Drive, Sd Or Mmc Card)
2. Press The Rec Button, It Will Take 3-5 Secondss To Read Memory Device. Then Usb Or Sd Icon Will Be Flashing.
3. Pressing Skip Up Or Skip Down Button To Select Desired Mode (Usb Or Sd) For Encoding. Then Press The Rec Button Again To Confirm. And
The System Is Starting The Encoding Mode After Few Secondss.
4. If Only Usb Drive Or Sd/Mmc Card Is Inserted, Step 3 Can Be Skipped.
5. The Usb Or Sd Icon Will Be Flashing On The Display Durnig Encoding.
14
TT 1070 E
