Idiomas disponibles
Idiomas disponibles
f)
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions, ta-
king into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
h)
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe hand-
ling and control of the tool in unexpected situations.
5) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety instructions for mitre saws
a)
Mitre saws are intended to cut wood or wood-
like products, they cannot be used with abra-
sive cut-off wheels for cutting ferrous materi-
al such as bars, rods, studs, etc. Abrasive dust
causes moving parts such as the lower guard to
jam. Sparks from abrasive cutting will burn the lo-
wer guard, the kerf insert and other plastic parts.
b)
Use clamps to support the workpiece whe-
never possible. If supporting the workpiece
by hand, you must always keep your hand at
least 100 mm from either side of the saw bla-
de. Do not use this saw to cut pieces that are
too small to be securely clamped or held by
hand. If your hand is placed too close to the saw
blade, there is an increased risk of injury from bla-
de contact.
c)
The workpiece must be stationary and clam-
ped or held against both the fence and the
table. Do not feed the workpiece into the bla-
de or cut "freehand" in any way. Unrestrained
or moving workpieces could be thrown at high
speeds, causing injury.
d)
Push the saw through the workpiece. Do not
pull the saw through the workpiece. To make a
cut, raise the saw head and pull it out over the
workpiece without cutting, start the motor,
press the saw head down and push the saw
through the workpiece.
Cutting on the pull stroke is likely to cause the saw
blade to climb on top of the workpiece and violent-
ly throw the blade assembly towards the operator.
e)
Never cross your hand over the intended line
of cutting either in front or behind the saw
blade. Supporting the workpiece "cross handed"
i.e. holding the workpiece to the right of the saw
blade with your left hand or vice versa is very dan-
gerous.
f)
Do not reach behind the fence with either
hand closer than 100 mm from either side of
the saw blade, to remove wood scraps, or for
any other reason while the blade is spinning.
The proximity of the spinning saw blade to your
hand may not be obvious and you may be seri-
ously injured.
g)
Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence. Al-
ways make certain that there is no gap bet-
ween the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be
no nails or foreign objects in the workpiece.
h)
Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the work-
piece. Small debris or loose pieces of wood or
other objects that contact the revolving blade can
be thrown with high speed.
i)
Cut only one workpiece at a time. Stacked mul-
tiple workpieces cannot be adequately clamped
or braced and may bind on the blade or shift du-
ring cutting.
j)
Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level
and firm work surface reduces the risk of the mitre
saw becoming unstable.
k)
Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support
the workpiece and will not interfere with the
blade or the guarding system. Without turning
the tool "ON" and with no workpiece on the table,
move the saw blade through a complete simula-
ted cut to assure there will be no interference or
danger of cutting the fence.
www.scheppach.com
GB | 31
