Bosch PWS 7-115 Manual Original página 22

OBJ_BUCH-1824-002.book Page 22 Monday, October 28, 2013 2:18 PM
22 | English
Angle Grinder PWS ...
Article number 3 603 ...
Rated power input
Rated speed min
Grinding disc diameter,
max. mm
Thread of grinder spindle
Thread length (max.) of
grinder spindle mm
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
17.10.2013
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section "After-
sales Service and Application Service".
2 609 007 738 | (28.10.13)
780-125 7800
CA2 7.. CA2 7..
W 780
-1
12000 12000
125
M 14 M 14
21
kg 1.8
/II
Protection Guard for Grinding
Adjust the position of the protection guard 6 to the require-
ments of the work process. For this, press the release lever 1
upward and turn the protection guard 6 to the required posi-
tion.
 Always adjust the protection guard 6 in such a manner
 Adjust the protection guard 6 in such a manner that
 The protection guard 6 may be turned only upon actua-
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
 Provide for sufficient dust extraction when cutting
The protection guard for cutting 10 is mounted in the same
manner as the protection guard for grinding 6.
850-115 850-125
CA2 7.. CA2 7..
780 850
12000 12000
125 115
M 14
21 21
1.8 1.8
/II /II
Place the protection guard 6 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 6 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 6.
sparking is prevented in the direction of the operator.
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
tection guard for cutting 10.
stone.
8000
CA2 7..
850 800
12000
125 125
M 14 M 14
21 21
1.8 1.8
/II /II
Bosch Power Tools