Idiomas disponibles
Idiomas disponibles
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool (see figures A – B)
GDR 18V-200 / GDX 18V-200:
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder as far as it will go and release the
locking sleeve (2) to lock the application tool.
Impact-proof screwdriver bits (12) can be inserted using a
universal bit holder (11) with ball catch.
Inserting the application tool (see figures B – C)
GDX 18V-200 / GDS 18V-200:
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
plication.
Slide the application tool (13) onto the square drive of the
tool holder (1).
Due to the way the system operates, the application tool
(13) will move around slightly in the tool holder (1); this has
no influence on the function/safety.
Bosch Power Tools
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
Some application tools (e.g. double bits) cannot be safely
secured in the tool holder.
Removing the application tool (see figures A – B)
Pull the locking sleeve (2) forward and remove the applica-
tion tool.
Operation
Method of Operation
The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in and tightening (impact mechanism in action).
The impact mechanism is activated as soon as the screwed
connection runs tight and load is therefore put on the motor.
The impact mechanism then converts the power of the mo-
tor to steady rotary impacts. When loosening screws or nuts,
the process is reversed.
Starting Operation
Inserting the battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Set the rotational direction switch (7) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (4) into the handle until you feel it engage and it is
flush with the handle.
Set the rotational direction (see figure D)
The rotational direction switch (7) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (8) is being pressed.
Right rotation: To drive in screws and tighten nuts, press
the rotational direction switch (7) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (7) through to the right
stop.
Switching on/off
To start the power tool, press and hold the on/off switch
(8).
The LED lights up when the on/off switch (8) is lightly or fully
pressed, meaning that the work area is illuminated in poor
lighting conditions.
To switch off the power tool, release the on/off switch (8).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (8) to varying extents.
A light pressure on the on/off switch (8) results in a low rota-
tional speed. Increased pressure on the switch causes an in-
crease in speed.
English | 15
1 609 92A 6HR | (16.03.2021)
