Metabo WEPBA 19-125 Q DS M-Brush Instrucciones De Manejo página 14

en ENGLISH
Machines with VTC, TC and VC electronics:
The electronic signal display (7) flashes
and the machine does not start. The restart
protection is active. If the plug is put into the
socket with the machine switched on, or if the power
supply is restored following an interruption, the
machine will not start up. Switch the machine off
and back on again.
10. Accessories
Use only original Metabo accessories.
See page 5.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Special safety guard for "hubbed wheels"
For use with "hubbed wheels". The safety guard
must overlap accessories by at least 3.4 mm.
B Cutting guard clip / guard for cut-off
grinding
Designed for work with cutting disc and diamond
cutting discs. Once the cutting guard clip is fitted,
the safety guard becomes a cutting guard.
C Extraction guard for cut-off grinding
Designed for cutting through stone slabs with
diamond cutting discs. With nozzle for extracting
stone dust using a suitable extraction unit.
D Extraction guard for surface grinding
Intended for grinding of concrete, screed, wood and
plastics with diamond cup wheels and/or fibre discs
and suitable sanding plates. With nozzle for
extracting stone, wood and plastic dust using a
suitable extraction unit. Not suitable for extracting
sparks or for grinding of metals.
E Dust filter
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
F Hand protection
Intended for work with backing pads, sanding
plates, wire brushes and support plates, sanding
pads, wire brushes and diamond Drill Bits for tiles.
Install hand guard under the additional side-
mounted handle.
G Multiple position bar for side handle
Permits numerous handle positions.
H Bar side handle
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If the connection lead is damaged, it must be
replaced by a special connection lead.
Contact your local Metabo representative if you
have Metabo power tools that need repairing. You
can find the addresses on www.metabo.com.
14
You can download a list of spare parts from
www.metabo.com.
12. Environmental protection
The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations regarding
environmentally compatible disposal and the
recycling of old machines, packaging and
accessories.
13. Technical specifications
Explanatory notes on the specifications on page 4.
Changes due to technological progress reserved.
Ø = max. diameter of the accessory
t = max. permitted thickness of the
max,1
clamping shank on accessory when
using 2-hole nut (15)
t =max. permitted thickness of clamping shank
max,2
on accessory when using "Quick"
clamping nut (1)
t = roughing disc/cutting disc:
max,3
max. permitted thickness of accessory
M = spindle thread
l = length of the grinding spindle
n* = no-load speed (maximum speed)
n * = no-load speed (adjustable)
V
I = Current at 120 V
120 V
m = weight without mains cable
* Machines with the designation WE... : Energy-rich,
high-frequency interference can cause fluctuations
in speed. The fluctuations disappear, however, as
soon as the interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value
h, SG
(surface grinding)
a = Vibration emission value
h, DS
(sanding with sanding plate)
a = Vibration emission value
h, P
(polishing)
K = Uncertainty (vibration)
h,SG/DS/P
Wear ear protectors!