Idiomas disponibles
Idiomas disponibles
GYSFLASH 51.12 CNT FV / 101.12 CNT / 103.12 CNT / 121.12 CNT FV /
123.12 CNT FV / 125.12 CNT FV / 101.24 CNT FV / 103.24 CNT FV /
GENERAL DESCRIPTION
Your GYSFLASH is a professional multifunctional charger with Inverter technology. Designed to support the batteries of demonstra-
tion vehicles or during the diagnostic work, it also guarantees an ideal quality of charge for the maintenance of the most advanced
models. This charger can be fitted with cables up to 8 m long. Changing the charging cables requires recalibration (see page 21).
It is considered a fixed device not a mobile product.
Your GYSFLASH is supplied with a software that includes 4 different modes to choose from:
• Charging mode: dedicated to the charging of lead-acid (sealed, liquid, AGM...) or lithium (LiFePO4) starter batteries.
• Power mode | Diag+ : Supplies the energy required during diagnostic work on the vehicle.
• Power mode | Showroom : Maintains the charge of the battery and supplies the energy required when using the consumers
of a demonstration vehicle.
• Tester Mode: Used to check the state of the battery and test the vehicle starting system and alternator.
Your GYSFLASH is SMART!
The original features of your GYSFLASH can be extended by adding specific charging modes and profiles using the USB port and
custom settings (see page 23).
Your GYSFLASH also offers the possibility to recover data from several hundred charging operations on your USB stick for analysis
on a spreadsheet.
Additional modules (such as printer, Ethernet port, etc.) can also be connected to the charger via its dedicated module socket.
Auto-Detect» function:
The GYSFLASH is equipped with the «Auto-Detect» function which automatically starts a charge
when a battery is connected to the charger. (To enable/disable this function see page 21)
Auto-Restart» function:
The «Auto-Restart» function offers the possibility of automatically restarting the charger in the event of a power failure.
(To enable/disable this function see page 21)
«Lock» function:
It is possible to lock the buttons on your GYSFLASH when it is used in a place open to the public or unattended. To activate/
deactivate the lock, press and hold
START UP
1. Connect the charger to the mains.
2. Set the switch, located at the back of the charger, to «ON».
3. Select the desired mode (Charge -> Showroom -> Diag+ -> Tester).
To access the «configuration» menu press the
CHARGE MODE
• Setting the mode:
Press the SELECT button for 3 seconds to activate the
1
modification of the mode settings.
2 Use the arrows to change the value of the parameter.
Press the SELECT button to accept the value and move
3
to the next parameter.
Charge type:
Profil
normal
AGM
Pb-CHARGE
water
Easy
Li-CHARGE
LFP/LiFePO4
16
16
25.48 CNT FV / 51.48 CNT FV / 53.48 CNT FV
and
for 3 seconds.
key for 3s :
Charging voltage
2.40 V/cell
Lead batteries of the types Gel, MF, EFB, SLA...
Most AGM lead-acid batteries including START and STOP.
2.45 V/cell
However, some AGM batteries require a lower voltage charge (Normal profile). Check
the battery manual if in doubt.
2.45 V/cell
Open liquid-type lead-acid batteries with cap.
Profile dedicated to lead batteries that automatically adapts the charging current
according to the size of the battery.
2.40 V/cell
However, for maximum charge optimization, it is recommended, when possible, to
use normal, AGM or liquid charge curves.
3.60 V/cell
Lithium batteries type LFP (Lithium Ferro Phosphate)
AUTO-DETECT
U=12.3V
Pb-CHARGE
1
liquid
50Ah
2
1- Type of charge
2- Charge profile
3- Rated battery voltage
4- Rated battery capacity
EN
12V
12V
3
4
