YATO YT-73460 Manual Original página 8

PRODUCT OVERVIEW
The car compressor allows you to infl ate tyres and other items such
as balls and mattresses with compressed air. The power supply from
the vehicle's electrical system allows for increased product mobility.
The correct, reliable, and safe operation of the device depends on
its proper use, so:
Reading and keeping the entire manual before the fi rst use of
the device.
The supplier shall not be held liable for any damage resulting from
failure to observe the safety regulations and recommendations
specifi ed in this manual.
ACCESSORIES
The product is supplied with a fl exible hose supplying compressed
air to the item to be infl ated and with adapters to infl ate products
other than vehicle tyres.
SPECIFICATION
Parameter
Catalogue number
Rated voltage
Rated power
Maximum pressure
Capacity
Hose length
Power cord length
Weight
SAFETY INSTRUCTIONS
CAUTION! Read all of the following instructions. Failure to do so
may result in electric shock, fi re, or personal injury.
FOLLOW THE INSTRUCTIONS BELOW
Do not use the product in an explosive environment containing fl am-
mable liquids, gases, or vapours.
Do not place the device near any heat or fi re sources.
Connect the device only to the power network with the voltage and
frequency indicated on the nameplate of the device.
The plug of the power cord must match the power socket. Do not
modify the plug. Do not use any power adapters to adapt the plug to
the socket. An unmodifi ed plug, which matches the socket, reduces
the risk of an electric shock.
O R I G I N A L
8
Units Value
YT-73460
[VDC] 12
[W] 180
[MPa / bar] 1 / 10
[l/min.] 40
[m] 1,0
[m] 3,0
[kg] 1,8
GB
After each application, unplug the power cord from the power socket.
The device is intended for indoor use only. Do not expose the device
to any precipitation or moisture. If water and moisture enters the
device, the risk of electric shock is signifi cantly increased. Do not
immerse the product in water or any other liquid.
Do not obstruct the ventilation openings and make sure they are
clear. Obstructed and/or clogged ventilation openings may cause
the device to overheat. This can lead to damage to the device or
cause fi re or electric shock.
Do not overload the power cord. Do not use the power cord to carry,
connect, or disconnect the plug from the power socket. Avoid any
contact between the power cord and heat sources, oil, sharp edges,
and moving parts. Damage to the power cord increases the risk of
electric shock. If the power cord is damaged (e.g. it is cut, its insula-
tion is melted), immediately unplug it from the wall socket, and return
it to an authorised service facility. It is not allowed to use the product
with a damaged power cord. It is not allowed to have the power cord
repaired. It must be changed for a new one at an authorized ser-
vice centre. When using extension cords, use extension cords with
power parameters such as those shown on the device's nameplate.
If you notice any damage to any part of the device, you must dis-
continue using it. In this case, the device must be taken to an au-
thorised service centre or replaced by yourself, if this is permitted by
the user's manual.
Turn off the device and unplug the power cord from the socket be-
fore you start any work on replacing parts, cleaning, or adjusting.
Switch off the device before replacing the accessories and unplug
the power cord from the socket.
This device may be used by children of at least 8 years of age and
by persons with reduced physical, mental abilities and persons with
no experience or knowledge of the device, if supervised or instructed
on its safe use so that the risks associated with it were understanda-
ble. Children should not play with the device. Children should not be
allowed to perform cleaning and maintenance of the product without
supervision.
Warning! Never exceed the maximum pressure of the pumped
products. Exceeding the maximum pressure can cause a sud-
den burst of the pumped product which can cause serious injury.
If no maximum pressure is indicated on the product (e.g. mattress),
check the hardness of the pumped product by pressing it with your
hand.
Never leave the product unattended during pumping.
The compressor is designed to be used for short periods of time
(maximum 10 minutes). Operation of the compressor for a long pe-
riod of time will cause overheating of the device and its damage.
Reduced performance or heating up of the area of the hose con-
nection to the casing means that the device has been running for
too long and is overheating. When this happens, turn off the device
immediately and leave it for at least 30 minutes to cool down before
restarting.
I N S T R U C T I O N S