Idiomas disponibles
Idiomas disponibles
6. COMPLETING THE INSTALLATION
6.3 Air circulation
The air intake and outlet must not be blocked or cove-
red in any way. They also need to be dusted/cleaned on
a regular basis.
6.4 Post installation checklist Air circu-
lation
Check that the front levelling feet have been properly
installed.
Check that the connection to the water system does
not have any leaks and that the closing tap is easily ac-
cessible.
Check that the electrical connection is correctly in-
stalled and that the multipole switch and socket are
easily accessible.
Check the perfect alignment of the appliance with
adjacent structures.
OD. 7491TST
7491TST
Check that all adhesive tape and external or internal
TST
temporary protective devices have been removed.
Check the perfect closing of the doors and the smo-
oth sliding of the drawers and shelves.
20
Testo e graÿca
MOD
MOD. 7491TST
A
MOD. 7491TST
A
MOD. 7491TST
A
B02900100
MOD. 7491TST
B02900100
A
B02900100
A
Testo e graÿca
Testo e graÿca
Testo e graÿca
Testo e graÿca
Testo e graÿca
B
6.5 Start up
>
To start the appliance, connect the plug to the elec-
trical mains: at this point, when opening the door,
the control panel will usually visualize the message
"Stand by", and all the panel keys be off
>
To turn on all the appliance compartments, press the
Unit
button for three seconds. The display will show
the message "Initial test" for approx. 2 minutes. After
this phase the compressors will start up and remain
on until the default temperature set up in the factory
is reached. Do bear in mind that this condition could
last several hours during which time the display will
continue to flash the 'Start Up Phase' message.
If the appliance is provided with an Ice Maker, prior to
switching it on make sure that the water filter cartrid-
ge is installed (unless water supply source is already
filtered by other means such as reverse osmosis).
Purge air from the water lines by enacting the 'Manual
Clean' function from the Menu->Functions->Water
Filter options. You may need to complete this sequen-
ce several times until you stop hearing air sputtering
from the ice maker fill tube.
Once you are satisfied that the system is purged of
air switch the Ice Maker on by touching the
which will illuminate.
Note
If the FlexMode drawer is configured as a Frid-
ge or a Fresco compartment the ice maker will
be disabled. Default mode for the FlexMode
drawer is Freezer.
MOD
A
A
B02900100
Testo e graÿca
B02900100
B
B02900100
Parti retro-illuminate - la parte nera è trasparente
C
bianco EB 61 - 62 ÿli
Fondo o ultimo passaggio:
bianco EB 61 - 62 ÿli
passaggio di nero coprente 602 -95 ÿli
bianco EB 61 - 62 ÿli
forato solo per le parti retro illuminate come da disegno "C"
www.universal.bertazzoni.com
bianco EB 61 - 62 ÿli
Fondo o ultimo passaggio:
Nomenclature: Grigio Whirlpool
Fondo o ultimo passaggio:
passaggio di nero coprente 602 -95 ÿli
Fondo o ultimo passaggio:
passaggio di nero coprente 602 -95 ÿli
forato solo per le parti retro illuminate come da disegno "C"
B02900100
Fondo o ultimo passaggio:
passaggio di nero coprente 602 -95 ÿli
forato solo per le parti retro illuminate come da disegno "C"
Nomenclature: Grigio Whirlpool
bianco EB 61 - 62 ÿli
bianco EB 61 - 62 ÿli
Fondo o ultimo passaggio:
passaggio di nero coprente 602 -95 ÿli
Fondo o ultimo passaggio:
forato solo per le parti retro illuminate come da
passaggio di nero coprente 602 -95 ÿli
forato solo per le parti retro illuminate come da disegno "C"
Nomenclature: Grigio Whirlpool
Nomenclature: Grigio Whirlpool
button
bian
bianco EB 6
bianco EB 61 - 62
Fond
Fondo o ul
pass
Fondo o ultimo pa
passaggio
fora
passaggio di nero
forato solo
forato solo per le p
Nom
Nomenclat
Nomenclature: Gr
9
