Idiomas disponibles
Idiomas disponibles
WARNING: When Mounting the Wall Holder
• Make sure beforehand that there are no hidden cables
in the wall that could damage you!
• Place the wall holder so that the appliance is not
exposed to direct sunlight or other heat sources.
Notes for Use
• The appliance is especially suitable for quickly vacuum-
ing small amounts of dry dirt or dust.
• It is furthermore suitable for vacuuming a limited amount
of wet dirt or liquids.
• Contaminated filters reduce the suction power of the
vacuum cleaner, which is why we recommend regular
cleaning of the dirt filters existing.
• The appliance is operated via charged battery.
• When the end of the accumulator capacity is reached,
the indicator light flashes for approx. 50 seconds during
operation. The appliance then switches off. Recharge the
accumulator.
• Charging is done via the power supply unit supplied.
Direct mains operation with the power supply unit is not
possible.
On / Off Switch
I = Appliance on
O = Appliance off
Nozzle Attachments
The various nozzle attachments are easy to attach and
detach.
Mounting the Wall Holder
Inserting the Plug of the Power Supply Unit
If you want to use the wall holder also as the charging
station, attach the plug of the power supply unit first. Refer
to the illustrations (A and B) on page 3.
1. Set the plug of the power supply unit with the flattened
sides into the wall holder. (Fig. A)
2. Turn the plug of the power supply unit at the metal end
by 90 °. If necessary, use pliers to help. The plug must
be firmly seated in the holder and must not be able to be
moved. (Fig. B)
3. Fix the cable in the cable guide.
Fastening the Wall Holder
Mount the charging station near a power socket.
1. Hold the wall mount against the wall with the drill holes at
the bottom of the mount. Mark 2 drill holes.
2. Drill the holes and insert the plugs into the wall.
3. Insert the screws through the holes of the wall holder.
4. Tighten the screws with a screwdriver hand-tight into the
wall plugs.
PC-AKS3034_IM_02.2023
Charging the Built-in Battery
1. Switch off the appliance.
2. Connect the power supply unit to the connection
socket (5). If you have prepared the wall holder as a
charging station, hang the appliance in it.
3. Connect the power supply unit to an approved power
outlet. Charge the appliance for 4.5 hours before using it
for the first time.
- The indicator light lights up red during charging.
- Once the battery is fully charged, the indicator light
lights up green.
- It is normal for the appliance to heat up during
charging.
4. Stop all other charging process after a maximum of
4.5 hours or once the indicator light lights up perma-
nently green.
CAUTION:
Always disconnect the mains plug from the socket after
charging.
Using the Appliance
1. Disconnect the appliance from the power supply unit.
2. Attach a nozzle if necessary.
3. Switch on the appliance with the switch.
Vacuuming Dry Dirt
• Only vacuum up dry dirt with a dry collection container
and a dry filter!
• The crevice nozzles or the brush nozzle are suitable for
vacuuming dry dirt.
Picking up Wet Dirt or Liquids
1. Empty the collection container before vacuuming liquids
or wet dirt.
2. Fit the attachment for wet vacuuming (9) or one of the
two crevice nozzles (10 / 13).
3. Note the MAX marking on the collection container. The
maximum collection amount is 170 ml.
4. If you want to remove the nozzle, hold the end of the
nozzle down. In this way you avoid unintentional leakage
of the liquid.
End of Use
1. Switch off the appliance.
2. Empty the collection container as described below. Clean
the filter insert after each use to restore the appliance to
full performance the next time it is used.
3. Then recharge the accumulator of the appliance.
9
14.02.23
