Idiomas disponibles
Idiomas disponibles
1.3.3
Structure of embedded warnings
Embedded warnings refer to an individual dangerous
step. Embedded warnings are placed before a danger‐
ous step. The remedies are embedded in the sequence
of actions.
SIGNAL WORD – type and source of danger. Possi‐
ble consequence if disregarded.
---
2.
Safety
2.1
---
Safety instructions
Voltage must be supplied to BAT 6120 via a grounded
mains voltage system.
The power supply cable and battery cable B+/B– must
be in perfect condition.
Only use the battery cable B+/B– supplied by Bosch.
Do not extend or shorten the battery cable B+/B–.
When using an extension cable, make sure that the to‐
tal current of all devices connected to this extension
cable does not exceed the permissible current for the
extension cable and the upstream fuse in the fuse
box.
Only charge batteries in well ventilated areas.
Avoid naked flames and spark formation when charg‐
ing batteries.
Do not attempt to charge non-rechargeable batteries.
Do not charge lithium iron phosphate batteries (LFP =
LiFePO4) without the battery management system
(BMS).
Switch off all electrical equipment in the vehicle
whilst charging (also applies to charging of exhausted
batteries).
Do not short-circuit battery terminals.
---
Battery hazard
Risk of chemical burns – Electrolyte leaking from bat‐
teries and accumulators may cause eye and skin burns.
Make sure that any leaking liquid (electrolyte) does
not come into contact with skin or eyes.
If electrolyte contacts the relevant areas, immediately
rinse with water and then consult a medical professio‐
nal.
Do not short-circuit batteries and accumulators.
---
Risk of fire, explosion – Batteries and accumulators
can cause burns and injury if overcharged (gassed) or
short-circuited.
No open flames or sources of sparks.
Do not smoke.
Ensure that there is sufficient ventilation and extrac‐
tion in enclosed rooms.
Do not short-circuit batteries and accumulators.
---
2.2
Target group
The product may only be used by trained and instruc‐
ted personnel. Apprentices or personnel undergoing
training or instruction may use the product only under
the continual supervision of an experienced person.
Children must be supervised to ensure that they do not
play with the product.
Robert Bosch GmbH
Work on electrical systems or equipment must only be
performed by qualified electricians or trained person‐
nel under the guidance and supervision of an electri‐
cian.
---
2.3
Other applicable documents
General safety instructions Bosch Automotive Aftermar‐
ket
https://help.boschdiagnostics.com/generalsafetynotes
BAT 6120 Help Center
https://help.boschdiagnostics.com/BAT6120
---
2.4
Intended use
BAT 6120 is a battery charger in the workshop area
used to charge 12 V vehicle batteries or to supply vehi‐
cles with current, e.g. during repair.
---
2.5
Foreseeable misuse
Misuse ( ) with corresponding intended use ( ):
Use outside the allowed ambient conditions.
Use the BAT 6120 only under the allowed ambient
conditions.
---
Battery terminals are connected or disconnected in‐
correctly.
When connecting or disconnecting, BAT 6120 must
be switched off.
Connecting: Connect the red battery terminal to the
positive terminal (+) first. Next, connect the black
battery terminal to the negative terminal (–).
Disconnecting: Disconnect the black battery terminal
first. Next, disconnect the red battery terminal.
---
2.6
Prerequisites
• Place the BAT 6120 on a solid subsurface or hook on‐
to the wall mounting.
• The installation location must have an adequate load‐
bearing capacity. Pay attention to the weight of the
BAT 6120 and the weight of the battery to be charg‐
ed.
• Note and maintain a safe distance of 0.5 m between
the BAT 6120 and battery.
• Protect the BAT 6120 against damp and moisture.
• Do not cover up the BAT 6120.
• On installing the BAT 6120 maintain a lateral clear‐
ance of at least 15 cm for ventilation.
---
2.7
Protective clothing and equipment
• Safety goggles
• Protective gloves
---
BAT 6120 | 9 | en
1 689 989 524 | 2022-04-01
