Milwaukee FSPE 110X Manual Original página 11

TECHNICAL DATA
Production code.............................................................................................................
Rated input ....................................................................................................................
Output ............................................................................................................................
Stroke rate under no–load .............................................................................................
Lengths of stroke ...........................................................................................................
Bevel cuts up to .............................................................................................................
Cutting depth max. in:
Soft- wood .................................................................................................................
Hard-wood .................................................................................................................
Steel ..........................................................................................................................
Non-ferrous metal ......................................................................................................
Aluminium ..................................................................................................................
Ceramics ...................................................................................................................
Weight according EPTA-Procedure 01/2014 .................................................................
Recommended ambient operating temperature ............................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ..............................................................
Sound power level (Uncertainty K=3dB(A)) ...................................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN
62841.
Cutting boards *1
Vibration emission value a .....................................................................................
h,B
Uncertainty K .............................................................................................................
Cutting sheet metal *2
Vibration emission value a .....................................................................................
h,M
Uncertainty K .............................................................................................................
*1 with saw blade T101B, dimension 75 x 8 x 1,4 mm and tooth pitch 2,5 mm
*2 with saw blade T118A, dimension 55 x 8 x 1 mm and tooth pitch 1,2 mm
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or
poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the
job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm,
organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow all instructions listed
below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
JIG SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a „live" wire may make exposed metal parts of
the power tool „live" and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
Wear ear protectors. Exposure to noise can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the
dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device
on again while the insertion tool is stalled, as doing so could trigger a sudden recoil
with a high reactive force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
20 ENGLISH
JIG SAW FSPE 110X (220-240V)
.........................4152 49 05...
...000001-999999
............................ 730 W
............................ 370 W
................... 500-3000 min
-1
.............................. 26 mm
.............................45°
............................ 135 mm
............................ 100 mm
.............................. 10 mm
.............................. 20 mm
.............................. 30 mm
.............................. 10 mm
............................. 2,5 kg
.................... -18...+50 °C
.............................. 87 dB (A)
.............................. 98 dB (A)
............................. 7,9 m/s 2
............................. 1,5 m/s 2
............................. 4,4 m/s 2
............................. 1,5 m/s 2
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or
waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage.
Always disconnect the plug from the socket before carrying out any work on the
machine.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light
building materials for walls). Harder materials (metals) must fi rst be drilled with a hole
corresponding to the size of the saw blade.
SPECIFIED CONDITIONS OF USE
This jig saw can cut wood, plastic and metal; it can cut straight lines, bevels, curves,
and internal cut-outs.
Do not use this product in any other way as stated for normal use.
EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 62841-1:2015
EN 62841-2-11:2016+A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2021-08-16
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and
that the following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016+A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2021-08-16
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Appliances used at many diff erent locations including wet room and open air must be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Connect only to single-phase AC current and only to the system voltage indicated on
the rating plate. It is also possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Make sure the machine is switched off before plugging in.
Under the eff ect of extreme electromagnetic interferences from the outside,
temporary variations in the speed of rotation could arise in particular cases.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the supply cord of this appliance is damaged, it must only be replaced by a repair
shop appointed by the manufacturer, to avoid hazardous situations.
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No.
as well as the machine type printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying out
any work on the machine.
Please read the instructions carefully before starting the
machine.
Accessory - Not included in standard equipment, available as an
accessory.
Do not dispose of waste electrical and electronic equipment as
unsorted municipal waste.
Waste electrical and electronic equipment must be collected
separately.
Waste light sources have to be removed from equipment. Check
with your local authority or retailer for recycling advice and
collection point.
According to local regulations retailers may have an obligation to
take back waste electrical and electronic equipment free of
charge.
Your contribution to re-use and recycling of waste electrical and
electronic equipment helps to reduce the demand of raw
materials.
Waste electrical and electronic equipment contain valuable,
recyclable materials, which can adversely impact the
environment and the human health, if not disposed of in an
environmentally compatible manner.
Delete personal data from waste equipment, if any.
Class II tool, tool in which protection against electric shock does
not rely on basic insulation only, but in which additional safety
precautions, such as double insulation or reinforced insulation,
are provided.
There being no provision for protective earthing or reliance upon
installation conditions.
n
Stroke rate under no-load
0
V
Volts
AC Current
European Conformity Mark
British Confomity Mark
Regulatory Compliance Mark (RCM). Product meets applicable
regulatory requirements.
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 21