Idiomas disponibles
Idiomas disponibles
that the grinding tool is correctly mounted and that it can be turn
freely, make sure that the grinding tool does not graze against the
protecting guard or other parts.
4. SPINDLE LOCK BUTTON (SEE FIG. G)
Clean the grinder spindle and all parts to be mounted. For clamping
and loosening the grinding tools, lock the grinder spindle with the
spindle lock button.
WARNING: Actuate the spindle lock button
only when the grinder spindle is at a
standstill!
5. HAND GRIP AREAS
Always hold your angle grinder firmly with both hands when operating.
6. SLIDE ON/OFF SWITCH (SEE FIG. H)
To start the power tool, first press the back of on/off switch, then
push the on/off switch forward.
To lock the on/off switch, press the on/off switch down at the front
until it engages.
To switch off the power tool, briefly press down the back of the on/
off switch and then release it.
NOTE: The machine is equipped with the function
of Accidental Start Protection. The machine will
not run when you put the battery on the machine
if switch is engaged "on" position to make sure
safety to user. The machine will work only after you
switching off and switching on again.
7. REMOVING THE GUARD
Never remove your guard for any other working conditions. To
remove, first take off the disc and both flanges. Then open the
clamping lever and rotate the guard to align the projections with
the gear case cut outs, then remove the guard. To re-fit the guard,
repeat this process in reverse. Keep all parts in a safe place.
8. TO USE THE GRINDER (SEE FIG. I)
ATTENTION: Do not switch the grinder on while the
disc is in contact with the workpiece. Allow the disc
to reach full speed before starting grinding.
Hold your angle grinder with one hand on the main handle and other
hand firmly around the auxiliary handle.
Always position the guard so that as much of the exposed disc as
possible is pointing away from you.
Be prepared for a stream of sparks when the disc touches the metal.
For best tool control, material removal and minimum overloading,
keep an angle between the disc and the workpiece surface at
approximately 15
to 30
when grinding.
o
o
Use cautiously when working into corners as contacting with the
intersecting surface may cause the grinder to jump or twist.
When grinding is complete, allow the workpiece to cool. Do not
touch the hot surface.
9. OVERLOAD
Overloading will cause damage to the motor of your angle grinder.
This can happen if your angle grinder is subjected to heavy use for
prolonged periods of time.
Never attempt to exert too much pressure on your angle grinder to
speed up your work.
The abrasive discs operate more efficiently when light pressure is
exerted, thus avoiding a drop in the speed of your angle grinder.
If your angle grinder becomes too hot, run it no load for 2-3 minutes
until it has cooled to normal operation temperature.
EN
10. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose of the
battery pack properly. This battery pack contains Lithium batteries.
Consult your local waste authority for information regarding available
recycling and/or disposal options. Discharge your battery pack by
operating your angle grinder, then remove the battery pack from
the angle grinder housing and cover the battery pack connections
with heavy duty adhesive tape to prevent short circuit and energy
discharge. Do not attempt to open or remove any of the components.
WORKING HINTS FOR
YOUR ANGLE GRINDER
1. Always start at no load to achieve maximum speed then start
working.
2. Do not force the disc to work faster, reducing the Disc's moving
speed means longer working time.
3. Always work with a 15-30 angle between disc and workpiece.
Larger angles will cut ridges into the workpiece and affect the
surface finish. Move the angle grinder across and back and forth
over the workpiece.
4. When using a cutting disc never change the cutting angle
otherwise you will stall the disc and angle grinder motor or break
the disc. When cutting, only cut in the opposite direction to the disc
rotation. If you cut in the same direction as the disc rotation the disc
may push itself out of the cut slot.
5. When cutting very hard material best results can be achieved with
a diamond disc.
6. When using a diamond disc it will become very hot. If this
happens you will see a full ring of sparks around the rotating disc.
Stop cutting and allow to cool at no load speed for 2-3 minutes.
7. Always ensure the workpiece is firmly held or clamped to prevent
movement.
MAINTENANCE
Remove the battery before carrying out any
adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry place. Keep the
motor ventilation slots clean. Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation slots. This
is normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
TROUBLESHOOTING
Although your new angle grinder is really very simple to operate, if
you do experience problems, please check the following:
1. If your grinder disc wobbles or vibrates, check if the outer flange is
tightened or if the disc is correctly located on the flange plate.
2. Do not use the damaged disc as it may disintegrate. Remove it
and replace with a new disc. Dispose of old disc sensibly.
3. If working on aluminum or a similar soft alloy, the disc will soon
become clogged and will not grind effectively.
4. A small amount of battery pack leakage may occur under extreme
temperatures or after heavy use. Immediately wash any leakage
from hands, skin or clothes with soap and water.
5. The power-draw from the battery generates heat. This is
19
