Idiomas disponibles
Idiomas disponibles
Double insulation (only for charger)
Not permitted for face grinding with abrasive
cutting off wheels
Read the operator's manual.
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction book
carefully.
1. CHARGING YOUR BATTERY PACK
A) CHARGING THE BATTERY
The battery charger supplied is matched to the Li-Ion battery
installed in the machine. Do not use another battery charger.
The Li-ion battery is protected against deep discharging. When
the battery is empty, the machine is switched off by means of a
protective circuit: The tool holder no longer rotates.
In a warm environment or after heavy use, the battery pack may
become too hot to permit charging. Allow time for the battery to cool
down before recharging.
When the battery pack is charged for the first time and after
prolonged storage, the battery pack will accept a 100% charge after
several charge and discharge cycles.
B) TO REMOVE THE BATTERY PACK (SEE FIG. A)
Depress the Battery Pack Release Button firmly first and then slide
the Battery Pack out from your tool.
C) TO INSTALL THE BATTERY PACK (SEE FIG. B)
Slide the fully charged Battery Pack onto the tool with sufficient
force until it clicks into position.
D) HOW TO CHARGE YOUR BATTERY PACK
CHARGING THE BATTERY (SEE FIG. C)
NOTE:
a) Do not use any charger other than that specifically provided for
use with the equipment.
b) If the battery pack is very hot you must remove your battery pack
from the charger and allow time for the battery to cool down before
recharging.
c) The battery in your new tool is not charged when it leaves the
plant. Therefore it must be full charged before using the first time.
d) Please charge the battery to reach full or no less than half charge
before storage. If the tool will not be used for long periods of time,
charge the battery every 3-6 months.
CHARGING PROCEDURE
1) Plug the charger into an appropriate outlet. The light will be green.
2) Slide the battery pack into the charger, the light will turn to red to
indicate the charging process has started.
3) When charging is completed, the light will turn to green. The pack
is now fully charged, unplug the charger and remove the battery
pack.
18
WARNING: When battery charge runs out after
continuously use or exposure to direct sunlight or heat, allow
time for the tool to cool down before re-charging to achieve
the full charge.
CHARGING INDICATOR
Light
Red on
Green on
OPERATING
INTENDED USE
The machine is intended for cutting, roughing and brushing metal
and stone materials without using water. For cutting metal, a special
protection guard for cutting (accessory) must be used.
1. INSTALLING AND ADJUSTING AUXILIARY
HANDLE (SEE FIG. D)
Before any work on the machine itself, remove the
battery pack from your tool.
For work with grinding or cutting discs, the wheel
guard must be mounted.
2. GUARD ADJUSTMENT (SEE FIG. E1-E3)
You have the option of two working positions to provide the safest
and most comfortable control of your angle grinder. The handle can
be screwed clockwise into either hole on the sides of the gear case.
NOTE: This handle should be used at all times to maintain
complete control of the tool.
Wheel guard for grinding
The coded projection on the wheel guard ensures that only a guard
that fits the machine type can be mounted.
Open the clamping lever. Place the wheel guard with coded
projection into the coded groove on the spindle of the machine head
and rotate to the required position (working position).
To fasten the wheel guard, close the clamping lever.
The closed side of the wheel guard must always point to the operator.
NOTE: With the clamping lever open the clamp adjusting nut can be
adjusted to ensure the guard is securely clamped after the clamping
lever is finally closed.
Wheel guard for cutting (not supplied)
WARNING: For cutting metal, always work with the wheel
guard for cutting.
The wheel guard for cutting is mounted in the same manner
as the wheel guard for grinding.
3. FITTING THE DISCS (NOT SUPPLIED) (SEE FIG.
F1-F3)
Put the inner flange onto the tool spindle. Ensure it is located on the
two flats of spindle.
Place the disc on the tool spindle and inner flange. Ensure it is
correctly located. Fit the threaded outer flange making sure it is
facing in the correct direction for the type of disc fitted. For grinding
discs, the flange is fitted with the raised portion facing towards the
disc. For cutting discs, the flange is fitted with the raised portion
facing away from the disc.
Press in the spindle lock button and rotate the spindle by hand until
it is locked. Keeping the lock button pressed in, tighten the outer
flange with the spanner provided.
NOTE: After mounting the grinder tool and before switch on, check
Status
Charging
Fully Charged
EN
