Using The Machine; Electrical Connection - Clatronic DB 3105 Instrucciones De Servicio

Connected Wattage
In total the device can consume 2000 W of power. With this
connected load a separate supply line protected by a 16 A
household circuit breaker is recommended.
CAUTION! Overload
Do not use any extension leads or multiple sockets as this
device is too powerful.

Using the Machine

NOTE:
This device should only be used for ironing garments and
textiles.
• Remove any protective films and adhesive labels from the
stainless steel soleplate before using the appliance.
• Completely unwind the line cord.
Ironing without steam (steam jet regulator on "O")
1. Place the iron on its stand (2).
2. Turn the steam regulator (8) to "O". Push it down if neces-
sary in order to turn it.
3. Always set the temperature control (5) to "0" before con-
necting the appliance to a power point, or before discon-
necting it.
4. Sort out the garments according to their ironing tempera-
tures. Start with the lower temperatures. It is set with the
thermostat (5):
● Synthetics, silk
● ● Wool,
● ● ● Cotton, linen
MAX

5. Electrical connection

• Make sure that the iron voltage (see name plate) and
the line voltage match.
• Only connect the machine to a properly installed
safety socket.
6. The control lamp (10) lights up. As soon as it shuts off,
the set temperature is reached. Now you can start to iron.
7. Always pull the plug out of the socket after using the iron.
Steam Ironing ( )
WARNING:
The steam is hot. Danger of scalding!
NOTE:
• In order to use the steam ironing function, the water tank must be filled.
• A high temperature is needed. Turn the temperature
regulator (5) to symbol "● ● ●" at the least.
• If the temperature is too low, water may leak from the
soleplate.
•
•
•
Refilling the water tank
1. Set the temperature regulator (5) to "0".
2. Always disconnect the mains plug before refilling water.
3. Set the steam control (8) to "O" (no steam). Fill in water
4. Close the filler opening.
Spray Function ( )
In order to moisten a section to be ironed press the spray but-
ton (9). Turn the button to the symbol and press it intermittently.
Vertical Steam (Vertical steam function)
This can be used to produce a jet of steam in a vertical direc-
tion.
low temperature
Never direct the steam jet at people. Risk of burning!
medium temperature
1. Hang your clothes on a hanger and hold the iron vertically
high temperature
maximum temperature
2. Set the temperature regulator (5) to symbol "● ● ●".
3. Turn the button (9) to the steam jet symbol
If the amount of steam emitted is too little, wait until the
appliance heats up again.
When you have finished
1. Always turn the temperature control to "0" after use and
2. Set the steam quantity regulator (8) to "O" position.
3. Empty the water tank in order to prevent the contents of the
4. Allow the device to cool down before you put it away.
Self-Cleaning (
1. Half fill the water tank with water.
2. Heat the machine up to its maximum temperature. After the
Use the steam quantity regulator (8) to set the steam
quantity.
O no steam
Small steam volume
Large steam volume
The steam starts escaping as soon as you bring the iron to
a horizontal position.
Extra steam can be added with the steam jet function " "
(9). Turn the button to the symbol and press it intermittently.
through the filling hole (7). Using a filling container. Do
not exceed the maximum line as marked on the water
reservoir.
WARNING:
at a distance of approx. 3-5 cm.
steam jet button intermittently.
NOTE:
remove the mains plug (The control lamp goes off).
tank leaking.
)
control lamp goes off remove the machine from the mains
supply.
. Press the
35