Storing Your Appliance - Char-Broil GRILL2GO X200 Instrucciones De Funcionamiento

Regulator locked in OFF position. Turn to
Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over appliance while lighting.
1. Turn regulator control knob to
2. Connect gas cartridge.
3. Open the grill lid.
4. Press and turn the regulator control knob to the
position.
5. Push ignitor button rapidly.
6. Once ignited, turn the control knob to the desired
setting.
7. If ignition does not occur in 5 seconds, turn the
regulator control knob to , wait 5 minutes, and
repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
Match Lighting
1. Place lit match next to burner. Turn regulator
control knob to .
2. If ignition does NOT occur in 5 seconds, turn the
regulator control knob to , wait 5 minutes and
repeat the lighting procedure.
Match Light Hole
Leak Testing Valves, Tube and
Regulator
Leak test at least once a year and every
time the cartridge is changed or
disconnected.
1. Turn appliance control knob to
2. Be sure gas cartridge is tightly connected to
regulator.
3 . If you hear a rushing sound , remove
cartridge immediately. There is a major leak
at the connection. Correct before
proceeding.
4. Brush soapy solution (mixture of half soap and
half water) onto hose connections and areas
circled below.
5. If growing bubbles appear, there is a leak. Check
cartridge for tigthness. If leak continous relace
cartridge and try again. If leak cannot be
stopped do not try to repair. Call for replacement
parts.
Regulator/Valve Installation/Removal
1. With knob pointing to right, insert Regulator/Valve
into end of burner (A)
Notch in Regulator/Valve MUST engage dimple
in end of burner.
2. Once Regulator/Valve has completely engaged
burner, turn Regulator/Valve counterclockwise (B)
to lock in position with knob pointing as shown (C).
3. To remove reverse steps.
to unlock.
A
postion.
Red notch
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
If your appliance is getting hard to light or the flame
is weak, check and clean the venturis and burners.
Spiders or small insects are known to create
"flashback" problems by building nests and laying
eggs in the appliance's venturi or burner obstructing
the flow of gas. The backed-up gas can ignite behind
the control panel. This flashback can damage your
appliance and cause injury. To prevent flashbacks
and ensure good performance, the burner and
venturi tube assembly should be removed and
.
cleaned whenever the appliance has been idle for an
extended period of time.
Cleaning The Burner Assembly
1. Turn gas off at regulator control knob and
disconnect gas cartridge.
2. Remove cooking grid.
3. Remove regulator from burner tube by (1) rotating
regulator until knob is to right and then (2) by pulling
outward. Shown FIG. A
4. Wipe ceramic electrode with rubbing alcohol and cloth.
Clean burner exterior with soap and water. insert
garden hose (preferably with nozzle), into burner tube
forcing water through tube. Make sure water comes
out of every porthole. Open clogged portholes with a
thin wire. Allow burner to dry thoroughly and
examine portholes. Due to normal wear and corrosion
some portholes may become enlarged, if so replace
burner. If any horizontal cracks appear from porthole to
porthole or large holes (other than portholes) are found
replace burner.
5. If barbecue is to be stored, coat burner lightly with
cooking oil. Wrap in protective cover to keep insects
out. If not storing use following steps.
6. Reattach regulator.
7. Replace cooking grid.
8. Before cooking again on barbecue, perform a "Leak
Test" and "Burner Flame Check".
B
Dimple
Full engagement
C
CAUTION
A
3

Storing Your appliance

•Clean cooking grates.
•Store in dry location.
•When gas cartridge is connected to appliance, store
outdoors in a well-ventilated space and out of reach
of children.
•Cover appliance if stored outdoors.
•Store appliance indoors ONLY if gas cartridge
disconnected, removed from appliance and stored
outdoors.
•When removing appliance from storage check for burner
obstructions.
General Appliance Cleaning
•
Clean appliance often, preferably after each
cookout. If a bristle brush is used to clean any of the
appliance cooking surfaces, ensure no loose bristles
remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surface while
appliance is hot. Appliance should be cleaned at
least once a year.
• Apply a strong solution of detergent and
water or use a appliance cleaner with scrub brush on
insides of appliance lid and bottom. Rinse and allow
to completely air dry. Do not apply caustic
appliance/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe
dry.
Do not use citrisol, abrasive cleaners, degreasers or
a concentrated appliance cleaner on plastic parts.
Damage to and failure of parts can result.
•Porcelain surfaces: Because of glass-like
composition, most residue can be wiped away with
baking soda/water solution or specially formulated
cleaner. Use nonabrasive scouring powder for
stubborn stains.
•Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe
dry with a soft nonabrasive cloth.
•Stainless steel surfaces: To maintain your
appliance's high quality appearance, wash with mild
detergent and warm soapy water and wipe dry with
a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish
to avoid damage. Do not use abrasive pad on
areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean
any of the appliance cooking surfaces, ensure no
loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking
surfaces while appliance is hot.
IF APPLIANCE FAILS TO LIGHT
Make sure gas is turned on at cartridge.
Make sure there is gas in the cartridge.
Does the ignitor make a sparking noise?
If yes check for spark at burner.
If no spark, check for damaged or loose wires.
If wires are OK, check for cracked or broken electrode,
replace if needed.
If wire or electrodes are covered by cooking residue,
clean electrode tip with alcohol wipe if needed.
If needed replace wires.
If ignitor continues to not work then use match.
If this appliance needs to be repaired please contact
your supplier or Kriswell A/S. Please see Kriswell A/S
contact information on page 40.
B
GB
Høyre
skinne