Idiomas disponibles
Idiomas disponibles
Dear Customer,
Thank you for choosing a extruder from the Ritmo range of products.
This manual is designed to illustrate the features and operating methods of
your new extruder welder model STARGUN LINK. It contains all the
necessary information and prescriptions for correct and safe use of the
equipment by professional operators. Please read all parts of the manual
carefully and keep it in a
safe place for future consultation and/or to transfer to any future
owners/users of the extruder. We are confident that you will enjoy getting
to know your new equipment and will be able to use it profitably for many
years to come.
1. FIELD OF APPLICATION
The STARGUN LINK is a mini portable extruder adapt to the welding by
extrusion of plastic material such as Polyethylene
(PE), Polypropylene (PP).
Examples of weldings
"V"
D_ K
Film Overlay
2. TECHNICAL FEATURES
LINK 20
1/8 – 5/32
Rod Diameter
inch
3 – 4 mm
Max Extrusion
5 lbs/h
Output
2.2 Kg/h
Weldable
PE, PP, PVDF
material
Rated Voltage
230V 50Hz
Rated Power
3.1 KW
[KW]
Noise
14.5 lbs
Weight
6.5 Kg
3. DIMENSIONS
on page 52
4. PARTS
on page 52
12
EN
"DV"
90°
External Angle
LINK 30
LINK 40
1/8 – 5/32 –
5/32 – 3/16
3/16 inch
inch
3 – 4 – 5 mm
4 – 5 mm
7 lbs/h
9 lbs/h
3.2 Kg/h
4 Kg/h
PE, PP, PVDF
PE, PP
230V 50Hz
230V 50Hz
110V 60Hz
3.2 KW 230
V
3.7 KW
2.7 KW 110V
L
= 78 dBA
wA
15 lbs
16 lbs
6.8 Kg
7.3 Kg
5. SAFETY CRITERIA
The use of STARGUN LINK is reserved exclusively for trained and suitably
skilled personnel in accordance with the regulations in force.
Use the extruder exclusively for the purpose described in section Field of
application" and in accordance with the operating and maintenance
instructions. Any other type of utilization is considered as improper use and
therefore prohibited because of the risk of serious injury of operators, other
persons and/or damage to the extruder and other property.
Immediately replace all worn or damaged parts using exclusively Ritmo
original spare parts.
All repairs on the extruder must be performed by skilled and qualified
personnel.
Context:
MOTOR & BLOWER
SHOCKING
HAZARD
Check that the electrical characteristics of the extruder correspond to
the specifications of the power supply line.
During connection phase between electrical board and electrical line,
verify the presence of safety differential and magneto-thermal devices
on electrical supply line.
If necessary, proceed with calibration. Inlets on electrical board must be
of type IEC 309 with minimum protection grade IP44. Do not expose the
extruder to rain or other liquids.
Make sure that isolating protections (for example gloves) are always
perfectly dry.
Do not expose electrical wiring or hydraulic hoses to chemical
substances or mechanical stress (e.g. pedestrian or vehicular traffic,
contact with sharp objects, pulling, etc.).
Disconnect the power socket outlet from the electrical power supply
when work with the extruder has been concluded or temporarily
suspended. Before using the extruder check the condition of individual
electrical system components, particularly insulating parts, cables, cable
glands and cable jaws.
Clean the extruder thoroughly after each session. Avoid the use of
solvent, petrol and abrasive substances which could damage insulated
parts of the extruder.
Connection cable must agree to regulation and
required power.
Connection must be done with plug IEC 309, IP67.
20 A 230-250V.
Small or humid places, building sites surrounded by metallic masses or
water (for example shipyards) require use of equipment fed in SELV
(very low safety tensions).
Context:
BLOWER, MELTING
CHAMBER AND
WELDING SHOE
RISK OF BURNING
Handle the extruder carefully.
Do not touch welding bead and near areas before complete cooling.
CHECK GROUND
CONNECTION
USE
PROTECTION
GLOVES
