Chicco NEXT 2 ME AIR Manual De Instrucciones página 23

Ocultar thumbs Ver también para NEXT 2 ME AIR:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
If, during the fixing operations of the crib to the parent's bed,
it is not possible to slide the feet of the crib under the parent's
bed, it is still possible to fix the crib following the operations
described in the previous points by rotating the adjustable feet
during alignment of the crib to the bed.
In order to rotate the feet pull the rotation release button using
one hand and turn the feet of the crib inward (fig. 27).
WARNING: Use of the product is only permitted with beds
and/or mattresses with straight sides. Use of the product with
round beds and/or mattresses or water beds is not permitted.
WARNING: When the product is used in the "Bedside sleeper
mode" (fixing to the bed, it should always be fitted to the long
side of access to the bed. DO NOT fix the product to the head
or bottom of the bed.
MAINTENANCE ADVICE
The crib and the mattress have a resistant fabric cover, which is
completely removable and washable.
The removal/application activities should be carried out by
adults only. On a regular basis check the condition of the prod-
uct and the presence of any possible damage. In the case of
damage do not use it and keep it out of the reach of children.
For washing of the fabrics, carefully comply with the instruc-
tions indicated on the label.
For cleaning do not use solvents, abrasive products or aggres-
sive products.
Hand wash in cold water
Do not bleach
C
Do not tumble dry
Do not iron
Do not dry clean
After each wash check the resistance of the fabric and of the
stitching.
WARNING: During the removal and/or application of the lin-
ing, handle the fabric carefully in order to avoid accidental
damage or tears.
WARNING: the removal and/or application operations may
take a few minutes and should be carried out by an adult.
MAKING THE BED
It is possible to unfasten the crib from the parents' bed in order
to make the bed easily. Just unfasten the grey buckles located
below the fabric finish.
To re-secure the crib to the parents' bed, pull once again the
belts to make sure the crib is properly and firmly secured to
the parents' bed. Pay attention to follow all the steps previously
mentioned in paragraph ''Bedside sleeper mode (Fixing to the
bed)'' .
REMOVABLE LINING
17. Remove the mattress and release the buttons on the lower
part of the fabric structure (fig. 28).
18. Press the buttons located on the legs' fastening point (fig.
29) and pull the upper tubular structure upward, removing
the fabric lining from the legs (fig. 30). Perform these opera-
tions on both sides.
19. Open the lateral zips on the window opening and press the
release buttons of the upper removable tubular structure
as explained in paragraph ''Bedside sleeper mode (Fixing to
the bed)'' . Then pull out the removable upper tubular struc-
ture (fig. 31), paying attention not to damage the internal
part of the lining.
20. Open the zip located on the upper edge of the crib and
remove the fabric lining completely (fig. 32).
DISASSEMBLING THE CRIB
The crib can be fully disassembled in order to store it in the bag
supplied with the product. To disassemble the crib, repeat the
operations described in points 17-18 of paragraph ''Removable
lining'' . Then unfasten the central support structure by pressing
the fastening pins on both crib's legs (fig. 33).
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as provided for by the instructions
for use.
The warranty shall not therefore apply in the case of damages
caused by improper use, wear or accidental events.
For the duration of warranty on conformity defects please re-
fer to the specific provisions of national laws applicable in the
country of purchase, where provided.
23
loading