Chicco Next2me Magic EVO Manual Del Usuario página 16

• Do not use the product with more than
one child at a time.
• Prolonged exposure to sunlight may cause
the colour of the product to vary in tone.
After prolonged exposure of the product
to high temperatures, wait a few minutes
prior to putting your child in it.
• WARNING: During use, make sure that
bedsheets, blankets, etc. do not invade the
crib space.
• Keep the product out of reach of children
when it is not in use.
COMPONENTS
WARNING: Before assembly, check that the product and all
of its components have not been damaged during transpor-
tation. Should any part be damaged do not use and keep out
of reach of children.
A. Leg support with wheel (x2)
A1. Height adjustment button
A2. Height indicator
A3. Attachment support for crib frame
A4. Fitting for central support
A5. Fitting for bottom bar
A6. Wheels with brakes
A7. Foldable foot release button
B. Foot with wheel (x2)
C. Bottom bar
D. Central support
E. Crib structure
E1. Upper frame
E2. Leg support inserts
E2.1 Rocking activation button
E2.2 Rocking deactivation button
E2.3 Button for releasing crib frame from leg supports
E3. Button for lowering drop side
E4. Crib bottom
E5. Attachment for upper frame strut
E6. Attachment for crib base strut
E7. Grey buckle
E8. Fabric
E8.1 Front vertical zippers
E8.2 Upper zipper
E8.3 Upper fabric attachment buttons
E8.4 Lower fabric attachment buttons
E8.5 Strap with snap buttons
F. Crib structure side uprights (x2)
G. Fastening straps (x2)
G1. Grey prong
G2. Red buckle
G3. Red prong
H. Mattress with removable lining
I. Bag
ASSEMBLY OF THE CRIB
1. Insert the feet "B" on the leg supports "A", making sure that the
hole present on each foot points inwards. To insert the feet,
push on the foot while also pressing on the metal pin present
on the frame (Fig. 1).
2. Insert the bottom bar "C" in its fitting "A5", pressing on the
metal pin until you hear the connecting click (Fig. 2). Repeat
the same step for the other leg as well.
3. Insert the central support "D" in the fittings "A4" present on
both of the legs, pressing on the metal pin until the connect-
ing click is heard (Fig. 3-4).
4. Hold the crib frame "E" and turn the upper part of the frame
"E1" by 90° (Fig.5). Repeat the same operation for the bottom
of the crib "E4" (Fig. 6).
5. Cover the upper part of the frame "E1" with the fabric "E8",
making sure to insert the leg support fittings "E2" and the up-
per attachments "E5" in the appropriate slots on the sides of
the fabric (Fig. 7).
6. Insert the strut "F" in the attachment at the bottom of the crib
"E6" making sure to also insert it in the upper attachment "E5"
at the same time, until the connecting click is heard (Fig. 8).
Repeat this operation on the other side.
7. Close the upper zipper "E8.2" (Fig. 9).
8. Close the upper fabric attachment buttons "E8.3" (Fig. 10).
9. Close the lower fabric attachment buttons "E8.4" (Fig. 11).
10. Fasten the straps with the snap buttons "E8.5" as shown in
figure 12.
11. Insert the leg support inserts "E2" in the attachments "A3"
found on each leg (Fig. 13). Be careful to position the struc-
ture "E" so that the front drop panel faces in the same direc-
tion as the foldable feet.
12. Insert the mattress "H" inside the crib structure, making sure
to orient the breathable net surface upwards.
13. Block the 4 wheels "A6" of the crib by lowering the levers
that activate the brakes (fig.15).
The crib is now ready to be used.
ADJUSTING THE CRIB HEIGHT
The height of the crib can be adjusted in 11 different positions.
14. To adjust the height, press the buttons "A1" on the leg sup-
port and lift or lower the crib structure "E" to the desired po-
sition (Fig.16). Release after hearing the click.
The base of the crib can be slightly inclined by adjusting the 2
leg supports to different heights (Fig. 17).
WARNING: The crib can be inclined by a maximum of 4 po-
sitions between one leg support and the other (e.g., right leg
support in position 5 and left leg support in position 1) (Fig. 18).
WARNING: The child's head must always be positioned near
the raised end (fig.19).
WARNING: Selecting different heights on the two sides of the
crib is not permitted when it is used in the co-sleeping con-
figuration.
ROCKING FUNCTION ACTIVATION
15. The rocking function can be activated by pressing the acti-
vation buttons "E2.1" (Fig. 20). To disable the function, simply
press the deactivation buttons "E2.2" (Fig. 21) and, subse-
quently, gently move the crib upwards or downwards until
a click is heard on both sides.
WARNING: If the crib has been used previously in "Side sleep-
ing configuration (fastened to the bed)", make sure that the
drop side is in the closed position and check that it has en-
gaged correctly.
WARNING: Always remember to deactivate rocking configura-
tion when using the product in "Side sleeping (fastened to the
bed)" or when the child is unattended.
WARNING: It is not possible to select different heights on the
two sides of the crib when in rocking function.
16