Idiomas disponibles
Idiomas disponibles
TFA_No. 60.2033_Anleitung
Digital alarm clock with induction charger
D: Back (Fig. 4):
D 1:
Control knob for adjusting the height of the charging coil
D 2:
LIGHT LOW/AUTO/HIGH switch
D 3:
USB-A port
D 4:
QI CHARGER ON/OFF switch
E: Bottom (Fig. 4):
E 1:
Power adaptor jack DC 9V, 2.5A
E 2:
Battery compartment
6. Getting started
• Remove the protective film from the display.
• Connect the attached power adapter to the alarm clock. Insert the power adapter
pin into the device jack and connect the plug to a wall socket.
• The device will alert you with a beep and all LCD segments will be displayed for a
short moment. 0:00 appears on the display.
• The device is ready for use.
6.1 Insert the batteries
• The 2 x AAA batteries will operate as a backup power source in case of power
failure.
• In pure battery operation, the display is activated briefly each time a button is
pressed. For a permanent backlight, to use the charging function and to save
battery life, use the supplied power adapter.
• Open the battery compartment and insert two new AAA 1,5 V batteries.
• Close the battery compartment.
7. Operation
7.1 Time setting
• Press and hold the SET button for 3 seconds. The hour digit flashes on the display.
• Press the
or
button to set the hours.
• Press and hold the
or
button for fast mode.
• Confirm the setting with the SET button.
• Set the minutes in the same way.
• Confirm the setting with the SET button.
• The display will show the current time. The colon between hours and minutes
flashes every second.
• Press and hold the
button for 3 seconds, the colon stops flashing.
7.2 Alarm time setting
• Press the SET button briefly.
• The hour digit and the alarm symbol start flashing.
• Press the
or
button to set the alarm hours.
• Confirm the setting with the SET button.
• Set the minutes in the same way.
• Confirm the setting with the SET button.
• The display will show the current time.
08.08.2022
11:43 Uhr
Seite 10
– 18 –
Digital alarm clock with induction charger
7.3 Activate alarm
• Slide the ALARM ON/OFF switch to the position ON.
• The alarm is activated. The alarm symbol appears on the display.
7.4 Alarm clock function
• When the adjusted alarm time is reached, the alarm rings. The alarm symbol flash-
es. The SNOOZE sensor button is active and appears at the top right of the display.
• If the alarm is not stopped manually, the ascending alarm tone automatically turns
off after two minutes and the alarm will be reactivated at the same set time on the
following day. The alarm symbol remains on the display.
• Press any button (
/
/ SET) or press and hold the SNOOZE sensor button for
3 seconds to turn off the alarm sound.
• When the alarm rings, press the SNOOZE sensor button briefly and the snooze
function is activated.
•
SNOOZE will be flashing and the alarm will be interrupted for 5 minutes.
7.5 Deactivate alarm
• Slide the ALARM ON/OFF switch to the position OFF.
• The alarm function is deactivated. The alarm symbol and the SNOOZE sensor button
disappear.
7.6 Display light
• You can adjust the brightness in 2 steps (LOW or HIGH) with the LIGHT LOW/AUTO/
HIGH slide switch.
• If the automatic brightness adjustment is activated (position AUTO), the brightness
is regulated via the light sensor, i.e. dim light switches on automatically as soon as
the light sensor registers darkness.
• Attention: Continuously illuminated display only works when using the power
adapter. To temporarily activate the display light in pure battery operation, press
any button.
8. Charging function
• Note: The charging function only works with the power adapter.
8.1 Inductive charging of your mobile phone
• Slide the QI CHARGER ON/OFF switch to ON.
• Place your mobile phone in the holder. Your phone should sit centred on the charg-
ing pad.
• Use the control knob to slide the charging coil into the ideal charging position.
• The white charging indicator light appears when your phone is successfully charg-
ing.
• The indicator light does not appear or a red LED flashes on the display if your
device is not positioned correctly, or if your device is not compatible with the Qi
standard. You may need to remove your phone cover.
• Compatibility may vary based on phone model. Please check your phone's manual
for details.
– 19 –
