Idiomas disponibles
Idiomas disponibles
from short-circuiting (e.g. by protecting them with
adhesive tape).
4.6
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- crystalline silica from bricks and cement and other
masonry products, and
- arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals,work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials, such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or an air purifier,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
5. Overview
See pages 2 and 3.
1 Mouth, shooting head, nail outlet, firing area
2 Trigger safety lock
3 Setting knob (nailing depth)
4 Trigger
5 Handle
6 Upper part of the tool
7 Trigger safety lock
8 Battery pack release button
9 Battery pack *
10 Capacity and signal indicator *
11 Capacity indicator button *
12 Hook
13 Magazine
14 Feed slide
15 Locking
16 On/Off button
17 Operation indicator
18 Operating mode indicator
19 Operating mode button
20 Nose cover
21 Nails, nail strips
* depending on equipment/not included in scope of
delivery
6. Initial Operation
6.1
Battery pack
Charge the battery pack (9) before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Battery packs have a capacity and signal indicator
(10) (depends on design variant):
- Press the button (11), the LEDs indicate the
charge level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
Removing and inserting the battery pack
WARNING! The trigger safety lock (2) and
trigger (4) must not be used during insertion
and removal.
Removing:
Press the battery pack release (8) button and
remove the battery pack (9).
Inserting:
Slide in the battery pack (9) until it engages.
7. Tool details,
testing the tool,
Initial operation
7.1
Switching on and off
WARNING! Never leave the tool switched on
to avoid accidents.
Switching on
Press and hold the on/off button (16) for more than
once second: Power indicator (17) lights up.
Note: Do not operate the trigger safety lock (2) and
do not pull the trigger (4) while switching on the tool.
Switching on is otherwise prevented.
Note: Automatic shut-down: If a switched-on tool is
not use for 30 minutes, it switches off automatically.
Switching off:
Press and hold the on/off button (16) for more than
one second: the power indicator (17) goes off.
7.2
Setting the operating mode
Press the button (19) to switch between the
operating modes.
ENGLISH en
17
