Connection Notes; Zero/Span Adjustment; Technical Data - Phoenix Contact MCR-VDC-UI-B-DC Manual De Instrucciones

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

5. Connection Notes

Caution: Danger! Never work on the
machine when live!
Table 1:
Selection of the input voltage range
(see also Fig. 3, page 6)
Input
Adjustment
voltage
range
(± 20 %)
[V DC]
0...±550 V (440 - 660)
0...±370 V (296 - 444)
0...±250 V (200 - 300)
0...±170 V (136 - 204)
0...±120 V ( 96 - 144)
0...± 80 V ( 64 - 96)
0...± 54 V ( 43 - 65)
0...± 36 V ( 28 - 43)
0...± 24 V ( 19 - 29)
If the voltage signal exceeds the voltage
range given at the input signal terminal
block by more than 15 % (at 0...±660 V
by more than 5 %), the input circuit can
be damaged!
12
6. ZERO-/SPAN Adjustment
Observe a module warm-up time of
4 minutes before the adjustment procedure!
The module is preset in the factory to
0-24 V input and 0...10 V output.
Two potentiometers on the front of
the module (Fig. 4) are available for
adjustment::
ZERO: adjustment of the zero point
SPAN: adjustment of the end value..
a) Zero point calibration
• Connect a calibration source to the input terminal
blocks (U
and GND1) and set a voltage of 0 mV.
(1-7)
• Set the output signal value with the "ZERO" potentiometer:
Voltage output (0...±10 V):
Current output (0...±20 mA):
b) End value calibration
• Use the calibration source to set the maximum voltage
used in the input voltage range (Table 1).
• Set the output signal value (U
= ±20 mA) with the SPAN potentiometer.
I
OUT
14
Input
Jumper / position
terminal
block
1
2
3
4
5
6
7
J / position 1
7
J / position 2
7
J / position 3
factory setting
U
= 0V,
OUT
I
= 0 mA
OUT
= ±10 V or
OUT
Selection of the Input Voltage Range
• Opening the device (Fig. 2)
The lock on the housing top is
released on both sides using a
screwdriver 1. The housing top
and the electronics can now be
pulled out approximately 3 cm 2.
• Jumper adjustment (Fig. 3)
Plug the jumper J onto the
desired position for the input
voltage.
Next, close the housing again until
you hear it engage.
A ZERO/SPAN adjustment
must be performed each
time the input or output
range is changed.

7. Technical Data

Order number
Measurement (input)
Input voltage range
Input resistance
Input voltage range
Input resistance
Adjustment:
Rated insulation voltage:
input/output
output/supply
Measurement (output)
Output signal
Fig. 4
Max. output signal
Line/load resistance
Ripple
General data
Supply voltage
Current consumption
Test voltage:
auxiliary power supply/signal
Transmission error
Cutoff frequency (3 dB)
Response time
Ambient temperature range
Temperature coefficient
Dimensions (W / H / D)
Conductor cross section
Housing material
MCR-VDC-UI-B-DC
28 11 11 6
0... (±550 / ±370 / ±250 /±170) V DC
( 550 / 370 / 250 / 170) kΩ
0... (±120 /±80 /±54 /±36 /±24) V DC
( 120 / 80 / 54 / 36 / 24) kΩ
± 20 %
ZERO
± 20 %
SPAN
± 660 V with non-grounded circuits
± 100 V with grounded circuits
50 V
U
A
± 10 V
± 15 V
> 10 kΩ
< 50 mV
SS
18.5 ... 30.2 V DC
< 50 mA
input / output
1.5 kV, 50 Hz, 1 min.
1.0 kV, 50 Hz, 1 min.
< 1 % from end value
40 Hz
12 ms (0-90 %)
-25 °C to 50 °C
< 0.015 %/K
(22.5 / 99 / 114.5) mm
2
0.2 - 2.5 mm
polyamide PA non-reinforced
2
V
7 0
V
5 0
V
7 0
V
2 0
5
1
6
7
8
1
Fig.2
J
1
54V
2
36V
HYBRID TV1
3
24V
PHOENIX
CONTACT
J
1
54V
2
36V
3
24V
Fig. 3
13
I
A
± 20 mA
± 30 mA
< 500 Ω
< 50 mV
SS
(AWG 24-14)
15
Tabla de contenido
loading

Tabla de contenido