Lutron Caseta DVRF-AS Guía De Instalación Rápida

Quick Install Guide
DVRF-AS
120 V~ 50 / 60 Hz 6 A
ONLY for use with:
Diva smart dimmer model number: DVRF-6L
Claro smart switch model number: DVRF-5NS
Please read before installing
English
WARNING: SHOCK HAZARD. May result in Serious Injury or Death. Turn off power at circuit breaker or fuse before installing.
3-Way Wiring with a Dimmer
IMPORTANT: Before disconnecting the existing devices, tag the wire connected to the different colored screw (typically black, but wire colors vary, and labeled COM). This is the Common wire. QUESTIONS? See www.casetawireless.com/support
Dimmer
Red
Blue
Black
Common
(tagged)
Ground wire
(bare or green)
Blue
Dimmer
Line Black Red
120 V~
50 / 60 Hz
NOTE: Ensure that the same wire connects to the blue wire at all locations.
NOTE: Main dimmer can be placed in any location.
NOTE: When using an accessory switch with a dimmer the black and red wires are reversible.
4-Way Wiring with a Dimmer
IMPORTANT: Before disconnecting the existing devices, tag the wire connected to the different colored screw (typically black, but wire colors vary, and labeled COM). This is the Common wire. QUESTIONS? See www.casetawireless.com/support
Location 1 Location 2 (middle)
Dimmer
Red
Blue
Black
Common
(tagged)
Ground wire Ground wire
(bare or green) (bare or green)
Blue
Line Black Red Black
120 V~ Dimmer
50 / 60 Hz
NOTE: Ensure that the same wire connects to the blue wire at all locations.
NOTE: Main dimmer can be placed in any location.
NOTE: When using an accessory switch with a dimmer the black and red wires are reversible.
Accessory Switch with a Dimmer
Single tap the button for On (to the preset level).
ON
Double tap the button for full brightness.
ON
Single tap the button for Off.
OFF
Press and hold the button (1 second) for 30 second delayed fade-to-off.
OFF
Accessory Switch with a Switch
Single tap the button for On.
ON
Single tap the button for Off.
OFF
Press and hold the button (1 second) for 30 second delayed off.
OFF
Limited Warranty:
www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf ©2022 Lutron Electronics Co., Inc.
Lutron, Diva, Caséta, Claro, and LED+ are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and other countries.
One to breaker and one
to light(s). For illustration
Common
purposes only.
(tagged)
Do not disconnect.
Ground wire
(bare or green)
Blue
Accessory
Black Red
Switch
Location 3
Accessory
Switch
Black
Blue
Red
Common
(tagged)
Ground wire
(bare or green)
Blue Blue
Red Black Red
Accessory Accessory
Switch Switch
Operation
24/7 Support: 1.844.LUTRON1 (USA / Canada)
Claro Smart Accessory Switch
How-to videos
www.casetawireless.com/3way
Disconnect Power
Accessory
Switch Switch
Red
Black
Blue
Blue
Black
Red
White
Line /
Hot
120 V~
Neutral
50 / 60 Hz
Light
Neutral
Location 1
Accessory
Switch
Black
Blue
Red
Common
(tagged)
Ground wire
(bare or green)
Line
Neutral
120 V~
Light
50 / 60 Hz
Neutral
Symptom
The load does not turn ON or no LEDs on the
dimmer or switch turn ON.
ON
The load turns ON and the main dimmer or
switch works, but accessory switch does not
work.
OFF
The load does not remain ON and main
dimmer or switch LEDs glow dimly or blink.
For more information, please visit www.casetawireless.com/support
+1.888.235.2910 (Mexico)
www.casetawireless.com/support
Important Notes
1. Install in accordance with all national and local electrical codes.
2. When no "grounding means" exists in wallbox, the National Electrical Code (NEC
a control to be installed as a replacement when a plastic faceplate with plastic fasteners is
used, or the circuit is protected by a ground fault circuit interrupter (GFCI). Lutron wallplates
meet this requirement. Cap or remove green wire before screwing control into wallbox.
3. Protect the control from dust and dirt when painting or spackling the wall.
4. Clean the accessory switch with a soft damp cloth only. Do not use any chemical cleaners.
For more information, please see www.lutron.com/cleaning
5. For indoor use only.
6. For 3-way or multi-location wiring, use only one Diva smart dimmer (DVRF-6L) or Claro smart
switch (DVRF-5NS) with up to 10 accessory switches.
7. Maximum wire length between the main control and the farthest accessory switch is 150 ft
(45 m).
3-Way Wiring with a Switch
One to breaker and one
Common
to light(s). For illustration
(tagged)
purposes only.
Do not disconnect.
Ground wire
(bare or green)
Blue
Switch
Black Red Black
NOTE: Ensure that the same wire connects to the blue wire at all locations.
NOTE: Main switch can be placed in any location.
NOTE: The black wire of the main switch must always connect or point towards line.
See www.casetawireless.com/3way for more details.
4-Way Wiring with a Switch
Location 2 (middle)
Switch
Red
Black
Blue
Blue
Black
White
Red
Ground wire
(bare or green)
Blue Blue
Black Red Black Red
Accessory
Switch
Switch
NOTE: Ensure that the same wire connects to the blue wire at all locations.
NOTE: Main switch can be placed in any location.
NOTE: The black wire of the main switch must always connect or point towards line.
See www.casetawireless.com/3way for more details.
Troubleshooting
Possible Cause
• Front Accessible Service Switch (FASS) on the main
dimmer or switch is pulled out to the OFF position.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Wiring error. Refer to the wiring diagrams above or go to
www.lutron.com/wiringwizard
• Wire connected to the blue wire on the main dimmer or
main switch is not the same wire connected to the blue
wire of the accessory switch.
• Blue wire is miswired to neutral wire or touching ground.
P/N 0302061 REV A
) allows
®
Accessory
Switch
Black
Blue
Red
Common
(tagged)
Ground wire
(bare or green)
Blue
Accessory
Red
Switch
Light
Location 3
Accessory Accessory
Switch Switch
Black
Blue
Red
Common
(tagged)
Ground wire
(bare or green)
Blue
Black Red
Accessory
Light
Switch