Operation; Cleaning - Scheppach NTS30 Premium Traducción Del Manual De Instrucciones Original

Installing the suction hose (a) (Fig. I)
Connect the suction hose (a) to the corresponding port,
depending on the desired use, on the wet and dry vac-
uum.
Vacuuming (Fig. I):
Connect the suction hose (a) to the suction hose port
(9). To do so, slide the end of the suction hose (a) with
the two nipples into the suction hose port (9) (A). Insert
the two nipples into the recesses. Once the suction
hose is fully inserted, turn it clockwise (B).
Blowing (Fig. J):
Connect the suction hose (a) to the blowing function
connection port (13). Slide the end of the suction hose
(a) with the two nipples into the blowing function con-
nection port (13). Insert the two nipples into the recess-
es. It is not necessary to turn it here.
Installing the metal extension tube (g), suction
hose (a) and nozzles (e / f) (Fig. K)
• Connect the metal extension tube (g) with the bent
end of the suction hose (a).
• Fit the floor nozzle (e) or joint nozzle (f) to the other
end of the metal extension tube (g).
• Push the slide piece forwards (A) to change the
length of the metal extension tube (g). (Fig. L)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. L)
9.

Operation

m WARNING!
Always make sure the device is fully assembled before
start-up!
m WARNING!
Switch the device off if liquid or foam emerges with the
exhaust air during wet vacuuming.
Switch on / switch off / automatic (Fig. M, N)
The ON/OFF switch (11) has three settings:
1. Switch setting 0: Off
2. Switch setting I: On
- Press the on/off switch (11) on position "I" tu turn
on the device.
- Press the on/off switch (11) on position "0" to turn
off the device.
3. Switch setting II: Automatic mode (the vacuum
cleaner will be switched on by an electric tool).
• Plug your electrical tool's cable into the automatic
socket (10) (fig. N).
• Connect the suction hose (a) to the suction connec-
tion (9) on your electrical tool. Check that the con-
nection is secure and airtight.
• Set the switch on the vacuum system to position "II"
= Automatic mode.
Dry vacuuming (Fig. G, H)
Use the HEPA filter (d) for dry vacuuming. The paper
filter bag (c) can be used in addition. This ensures that
the HEPA filter (d) remains free of dust for longer and
maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the filters are correctly fitted.
Wet vacuuming (Fig. F)
Use the foam filter (b) for wet vacuuming. Ensure that
the foam filter (b) is correctly fitted.
If the stainless steel container (8) is full, the safety float
valve (14) closes the suction port and suction operation
is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(b) provided.
Water drain plug (7) (Fig. O)
The stainless steel container (8) is equipped with
a water drain plug (7) in order to make it easier to
drain. Open the water drain plug (7) by turning it coun-
ter-clockwise and drain out the liquid.

10. Cleaning

m WARNING!
Prior to any adjustment, maintenance or service work
disconnect the mains power plug!
Cleaning
It is recommended to clean the device after each use.
Do not spray the device with water or clean it under
running water. This can result in electric shocks and
can damage the device.
www.scheppach.com GB | 21