vigation buttons (55) to select the point "Back to
station" and confi rm with the "OK" button (56).
Press the "START" button (53) and then close the
display cover (23). The robot lawn mower will now
follow the perimeter wire (18) in a counterclock-
wise direction. Observe the robot lawn mower
during the complete trip along the perimeter wire
(18) until it is back in the charging station (19). If
the robot lawn mower has any problems at any
points, correct the perimeter wire (18) if neces-
sary and repeat the operation. The rechargeable
battery of the robot lawn mower will now be fully
charged. If any problems occur with docking, you
may need to reposition the charging station (19)
sideways until docking works without any prob-
lems.
To stop the robot lawn mower at any time, press
the red STOP button (3). When you press the
STOP button (3), the robot lawn mower will come
to a stop and wait for further instructions.
5.8 Securing the charging station
Once the robot lawn mower is working properly
and a suitable position for the charging station
(19) has been found, the charging station (19)
must be fi xed in place using the fastening screws
(15). Use the hexagon key (22) to secure the fas-
tening screws (15) fully in the ground. (Fig. 7c)
5.9 Battery charge level indicator
Press the button for the battery charge level indi-
cator. The battery charge level indicator indicates
the charge state of the battery by means of 3
LEDs (Fig. 13b).
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Anl_FREELEXO_LCD_BT_plus_SPK13.indb 40
Anl_FREELEXO_LCD_BT_plus_SPK13.indb 40
GB
Important!
When using a multi-Ah pack (e.g. 4-6Ah), always
set the higher capacity. Thanks to the gentle
charging and discharging of the robot lawn mower
there is no need to use the lower capacity in order
to extend the working life.
5.10 Charging the rechargeable battery with
the charger
In normal operation the battery (A) of the robot
lawn mower is charged via the charging station
(19). For independent use of the battery (A) from
the Power-X-Change series it can also be char-
ged in the external Power-X-Charger. Important!
– Depending on the model of your robot lawn mo-
wer, it might not come complete with the battery
charger (Fig. 13a/Item B).
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(B) into the socket outlet. The green LED will
then begin to fl ash.
2. Insert the rechargeable battery (A) into the
battery charger (B) (Fig. 13a).
3. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
- 40 -
05.10.2022 11:10:35
05.10.2022 11:10:35