SOLAC ME7711 Instrucciones De Uso página 8

USE
Remove the protective fabric cover (14).
•
Fit the head corresponding to the desired mas-
•
sage onto the head adaptor (Fig. 3)
You may alternate the use of different heads
•
during the same massage.
Extend the cable completely before plugging
•
it in.
Connect the appliance to the mains (Fig. 1).
•
Move the switch (2) to the massage position
•
(Fig.2 B) or to the "massage + infrared position
(IR) position" (Fig.2 C) according to the desired
massage.
Set the intensity of the massage using the in-
•
tensity control (3) and place the massager on
the area on which you are going to work.
Use the massage controller to set the intensity,
•
using your finger to turn the controller (3) one
way or the other depending on the desired set-
ting (Fig. 4)
Hold the appliance firmly with both hands and
•
move it over the skin in the direction of the
blood circulation (see "Massage Direction").
Without pressing too hard, simply glide the
•
massager over the area to be treated. Press-
ing the appliance too hard against the skin will
prevent the motor from operating efficiently.
MASSAGE DIRECTION
Always glide the appliance over the skin in the
•
direction of the blood circulation. In an upward
direction.
NEVER directly massage the spine.
•
NEVER directly massage a bone (knee, ankle,
•
elbow). The protruding parts of the massage
head could hit the bone, causing an injury.
- Legs: Place the appliance on the thigh,
close to the knee, and glide it gently
upwards towards the hip (Fig. 5)
- Buttocks: Combine upward and circular
movements. (Fig. 6)
- Abdomen: Place the appliance on the
navel and move it gently outwards (Fig 7).
Never make circular movements around
the navel.
- Arms: Place the appliance close to the
elbow and glide it gently towards the arm-
pit. Repeat the massage from the armpit
towards the elbow (Fig. 8)
- Back: Place the appliance in the area
of the spine and glide it gently upwards
towards the shoulder blade (fig. 9)
CHOOSING A MASSAGE HEAD
- FINGER-PRINT (7): "finger massage".
Moving pressure tips.
- MAX-FORCE (8 & 13): "Serrated roller"
head. Moving, vibrating helixes. This
tones the muscles, reduces volume,
warms up the muscles, relaxes and
relieves stress, for example.
- PRO-WAVE (10): "Wave shaped" head,
tones and improves blood circulation. For
use on the thigh and buttock areas.
- Fabric cover (12): For exclusive use with
the PRO-WAVE toning head. For greater
comfort cover the head with the fabric
cover. Never use it with creams.
- ROLL-MASSAGE (11): "Smooth roller"
head.
- DRY BRUSH (9): Exfoliating brush,
removes dead skin and stimulates blood
flow.
- BALL MASSAGE HEAD (12): Stimulates
and tones the muscles, helping to firm the
skin.
SKIN PREPARATION
It is essential to start by preparing the skin
•
properly before performing the massage in the
area where it is required, so we should exfo-
liate the skin using the natural bristle brush
(DRY BRUSH), which will leave the area free
of dead cells and make the skin softer. Avoid
damaging the skin through excessive exfolia-
tion (once per week is sufficient). Gently mas-
sage the entire area for 5 minutes. This step
helps to stimulate your blood circulation and
metabolism.
The skin should always be brushed toward the
•
heart, starting with the feet and moving up to
the hips in the case of legs, and from wrist to
shoulder for arms. Persist on rougher areas
and be careful with sensitive areas. Adjust the
intensity of exfoliation based on the condition
of the skin, the body area and particular sen-
sitivity.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE
Move the switch (2) to the"off" position (fig.2 A).
•
Unplug the appliance from the mains.
•
Clean the appliance
•
EN