Dimplex LVA231 Manual De Instrucciones página 6

Living Art Range
Model(s): LVA231 & LVA232
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should
be followed to reduce the risk of fire, electric shock, and injury
to persons, including the following:
If the appliance is damaged, check immediately with the
supplier before installation and operation.
Do not use this appliance in the immediate surroundings of a
bath, shower or swimming pool.
Do not use outdoors.
WARNING: With the heat 'On' (indicated by red LED - see 'y'
in detail A in Fig. 1) areas to the left and right of the glass
screen will become hot. However momentary contact with any
part of it should not cause injury.
WARNING: DO NOT OBSTRUCT AIR VENTS AT THE TOP AND
BOTTOM OF THE APPLIANCE AS CONSEQUENT
OVERHEATING CAN CAUSE DAMAGE
In the event of a fault switch off the appliance.
Switch off the appliance when not required for long periods.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they do
not play with the appliance.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or similarly qualified person
in order to avoid a hazard.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
This appliance must be used on an AC ~ supply only and the voltage
marked on the appliance must correspond to the supply voltage.
Do not switch the appliance on until properly installed. Please read
all the safety warnings and operating instructions.
General
Unpack the appliance carefully and retain the packaging for possible
future use, in the event of moving or returning the appliance to your
supplier.
Contents of Carton
• Living Art Range Model
• Wall fixing plate (attached to chassis for transit)
• Fixing screws and wall plugs
• Remote control and batteries (AAA type)
• Cable and plug
The appliance can be operated remotely or manually - see 'Operation'.
General features of the remote control are:
• Selection of 8 different scenes.
• Sound effects relevant to your selected scene may be
activated and the volume increased or decreased.
• Switch off to Standby indicated by red LED on left - see 'x' in
detail A in Fig. 1.
• Heat On/Off red LED on right indicates heat 'On' - see 'y' in
detail A in Fig. 1.
Installation
Do not connect appliance until properly fixed to the wall and the
Instruction leaflet is read fully.
For installation of the appliance, care must be taken not to damage
any cables that may be concealed in the wall.
Please be careful while drilling the holes.
- 1 -
These models are designed to be permanently wall mounted - see
Fig. 1 for recommended fixing dimensions from floor to underside of
the appliance for optimum viewing of the display screen. The outline
of the chassis and the position of the electrical socket are shown as
dotted outlines in Fig. 1. Any dimensions indicated '*' are recommended
dimensions.
The wall plate is secured to the chassis with 2 screws (see detail view
'X' in Fig. 4). To wall mount the appliance first remove the wall plate
from the chassis by removing the two screws and rotating the corner
hinges away from the chassis.
Note : Retain the two screws for future use.
Fix the wall plate to the wall using the wall plugs and screws provided.
(Note: Ensure that the wall is suitable for the screws & plugs provided).
Use the wall plate as a template to mark the hole positions for drilling
- see Fig. 2. Drill and fix the wall plate in position with one screw
initially to check the plate is level before marking and drilling the
remaining holes - see '1' in Fig. 3. Ensure the wall plate is fitted the
correct way up i.e. the side hooks are pointed upwards - see Fig. 3.
The appliance can then be fitted to the wall plate by aligning the slots
on the chassis with the side hooks on the wall plate. This is best
achieved by positioning the appliance vertically above the plate (see '2'
in Fig. 3) and locating on the side hooks and sliding the chassis
downwards (see '3' in Fig. 3).
The corner hinges on the wall plate may be used to secure the
appliance against inadvertent dislodgement. Simply rotate the hinges
upwards (see Fig. 2 and detail view in Fig. 3) to a position above the
chassis. They can then be screw fixed using the screws removed earlier
(see detail view 'X' in Fig. 4 of corner hinge rotated up and screw fixed
in position).
NOTE: The appliance should be 'HARD' wired to a fused switched
spur located behind the glass screen so as to be hidden from view -
see 'a' in Fig. 1. The cable should be shortened as necessary in order
to remain concealed behind the glass display screen.
Please consult a qualified electrician for appropriate wiring requirements.
Operation
Plug in the connector from the electrical hard wiring outlet to the
appliance (see '2' in detail B Fig. 1).
The illuminated power 'On' switch (see '3' in detail B Fig. 1) must first
be switched 'On' to operate the appliance either manually or by remote
control.
The 'Coal' scene will automatically come on when the power 'On' switch
is switched on.
Switch the heat 'On' if required (see '4' in detail B Fig. 1). Heat 'On'
will be indicated by a red LED (see 'Y' in detail 'A' Fig. 1).
Note: The temperature of the glass will rise steadily up to a maximum
of approximately 60 degrees C when the heat is turned 'on'.
The Memory Card (see 'y' in Fig. 6) as fitted is held in position by a
hinged cover (see 'x' in Fig. 6) which is screwed in place to provide
protection against damage in handling and for added security - see C
in Fig. 6.
If required the card can be removed by unscrewing and hinging back
the cover - see A in Fig. 6, and simply
(see 'z' in Fig. 6) beside the card to eject it.
In replacing the card it should drop down into position before pressing
home – see B in Fig. 6 (force should not be used in fitting the card as
damage can result). Ensure the logo on the card is facing down when
inserting it, as shown in A in Fig. 6.
Important: Always switch off the appliance before removing the
card.
Failure to do so will result in a picture freeze. To restart, the appliance
must first be turned off at the illuminated power 'On' switch - see '3' in
detail B in Fig. 1 and the card pressed into position, and then the
illuminated power 'On' switch turned on again.
UK
pressing down on the button