Important - Mellerware Vapour II 1600W Manual De Instrucciones

CAUTION: Iron from low temperature first then move
to high temperature fabrics. Should you need to iron at
a low temperature, after using a high temperature you
must wait for the pilot light to illuminate again, or you
will burn your clothes onto the iron. This will void the
warranty.
3.4. Dry ironing:
3.4.1. Make sure the temperature selection knob is at
the lowest level.
3.4.2. Set the iron on the support base on a steady,
firm surface.
3.4.3. Plug the appliance to the electrical power supply
and turn temperature selection knob to desired level,
the ready indicator light will turn on.
3.4.4. Once the light turns off, you may star to iron
over steady and firm surface.
3.4.5. When you have finished, turn the temperature
knob back to the lowest level, unplug from the electrical
power supply and wait until the appliance cools down
completely, before you proceed to store it.
IMPORTANT: If the iron contains water inside the tank
and you prefer dry ironing, move the steam control
lever to "0" position.
3.5. Steam ironing:
3.5.1. Make sure the appliance is unplugged from the
electric power supply, fill up the water tank. Make sure
not to overfill the tank.
3.5.2. Ensure the temperature selection knob is at the
lowest level, before plugging in the appliance.
3.5.3. Set the iron on its support base on a steady and
firm surface.
3.5.4. Plug in the iron and set the steam control lever
to the medium level.
3.5.5. Turn the temperature selection knob to the
desired level, suited for steam generation and the ready
indicator light should turn on.
3.5.6. Once the light turns off you may start ironing on
a steady and firm surface.
IMPORTANT: It is important to let the light to turn after
reaching the optimal temperature, otherwise the appli-
ance may experience leakage
3.5.7. Once you have finished its use, turn the
temperature selection knob back to the lowest, unplug
the appliance from the electrical power supply and
make sure to wait until completely cools down before
storing it.
IN ORDER TO STEAM IRON, HIGH TEMPERATURES
SHOULD BE SELECTED AT THE TEMPERATURE INDI-
CATOR KNOB.
3.6. Spray:
Spraying garments helps smooth out wrinkles to make
ironing easier.
3.6.1. Point the tip of the iron where you want to spray
the water and press the spray button.
3.6.2. Iron the garment as usual. To use this function, it
will be necessary to fill the water tank.
3.7. Burst of steam.
Steam ironing reduces ironing time and takes care of
the appliance.
3.7.1. Press the burst of steam button. Wait a few
seconds until the steam penetrates the fibres of the
garment before pushing the button again. For optimum
steam quality, do not apply more than three successive
bursts.
3.7.2. The spray button has to be pressed repeatedly to
release the first spray.
3.8. Vertical Ironing:
It is possible to iron hanging curtains, items of clothing
on their own hanger, etc. To do so, follow the below
instructions:
3.8.1. Select the irons maximum temperature by turn-
ing the iron's temperature regulator clockwise.
3.8.2. Iron from top to bottom while pressing the steam
control button. Important: for cotton and linen, it is
recommended to put the base of the iron in contact
with the material. For other more delicate fabrics, it is
recommended to keep the base of the a few centime-
tres away.
3.9. Self-cleaning:
3.9.1. It is important to self-clean the appliance at least
once a month to remove calcium and any the built-up
minerals inside the iron.
3.9.2. Fill the water tank to its maximum level.
3.9.3. Place the iron in an upright position, plug into the
mains and select the maximum temperature.
3.9.4. Leave the appliance to heat up until the indicator
light turns off.
3.9.5. Unplug the appliance and place it in the sink.
3.9.6. Let the water flow out through the steam vents in
the base, while lightly shaking the appliance.
3.9.7. Release the button after a minute or when the
tank becomes empty.
3.9.8. Leave the iron in the upright position until it has
cooled.
3.10. How to deal with scale build up:
3.10.1. For the appliance to work correctly it should
be kept free of lime scale or magnesium incrustations