English
Technical Specifications
M910x-xGA-1S / M9104-IUA-1S
Product Codes
M9102-AGA-1S
Power Requirements
Control Type
Input Signal
Feedback Signal
Motor Input Impedance
200 ohms Nominal
Running Torque
Travel Time
30 Seconds at 60 Hz
(for 90° of Rotation)
36 Seconds at 50 Hz
Rotation Range
93° ±3°, CW or CCW
Cycles
100,000 Full Stroke Cycles;
2,500,000 Repositions at Rated Running Torque
Audible Noise Rating
35 dBA Nominal at 1 m
Electrical Connections
1.2 m Polyvinyl Chloride (PVC) cable with 0.75 mm
Mechanical Connections
Up to13 mm Diameter Round Damper Shafts, or 10 mm Square Damper Shafts
Enclosure
IP 42
Ambient Conditions
- Operating
-20 to 60 °C; 90% RH Maximum, Noncondensing
- Storage
-40 to 85 °C; 90% RH Maximum, Noncondensing
Shipping Weight
0.5 Kg
Johnson Controls, Inc., declares that these products are in compliance with the essential requirements and other relevant provisions of the EMC Directive
Compliance
and Low Voltage Directive
M910x-xGA-5S
Product Codes
Power Requirements
AC 24 V +25% / -20% at 50/60 Hz
Safety Extra-Low Voltage (SELV) Class II
Control Type
Input Signal
Feedback Signal
---
Motor Input Impedance
200 ohms Nominal
Running Torque
Travel Time
30 Seconds at 60 Hz
(for 90° of Rotation)
36 Seconds at 50 Hz
Rotation Range
93° ±3°, CW or CCW
100,000 Full Stroke Cycles;
Cycles
2,500,000 Repositions at Rated Running Torque
Audible Noise Rating
35 dBA Nominal at 1 m
Electrical Connections
M3 Screw Terminals
Mechanical Connections
Up to13 mm Diameter Round Damper Shafts, or 10 mm Square Damper Shafts
Enclosure
IP 40
Ambient Conditions
- Operating
-20 to 60 °C; 90% RH Maximum, Noncondensing
- Storage
-40 to 85 °C; 90% RH Maximum, Noncondensing
Shipping Weight
0.5 Kg
Compliance
Johnson Controls declares that these products are in compliance with the essential requirements and other relevant provisions of the EMC Directive
and Low Voltage Directive
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson
Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its products.
2
M9102-xGA-xS / M9104-xGA-xS / M9104-IUA-1S
M9104-AGA-1S
AC 24 V +25% / -20% at 50/60 Hz
2.1 VA
Floating Control without Timeout
AC 24 V +25% / -20% at 50/60 Hz, SELV or Class II
2 Nm
4 Nm
60 Seconds at 60 Hz
72 Seconds at 50 Hz
M9102-AGA-5S
M9104-AGA-5S
2.1 VA
Floating Control without Timeout
AC 24 V +25% / -20% at 50/60 Hz, SELV Class II
2 Nm
60 Seconds at 60 Hz
72 Seconds at 50 Hz
M9102-IGA-1S
M9104-IGA-1S
2.5 VA
ON/OFF and Floating Control With Timeout
---
2 Nm
30 Seconds at 60 Hz
36 Seconds at 50 Hz
2
conductors and 6 mm ferrule ends
M9102-IGA-5S
2.5 VA
ON/OFF and Floating Control With Timeout
4 Nm
2 Nm
30 Seconds at 60 Hz
36 Seconds at 50 Hz
This document is subject to change without notice
M9104-IUA-1S
AC 100 to 240V -15%/+10%
at 50/60 Hz
3.0 VA
7.5 VA Supply and 0.07 A
AC 100 to 240V -15%/+10%
at 50/60 Hz Class II
4 Nm
60 Seconds at 60 Hz
72 Seconds at 50 Hz
M9104-IGA-5S
3.0 VA
60 Seconds at 60 Hz
72 Seconds at 50 Hz
M9104-GGA-1S
AC 24 V +25% / -20%
at 50/60 Hz
3.6 VA
Modulating
DC 0(2) to 10 V
or 0(4) to 20 mA
with field furnished
500 ohm resistor
DC 0(2)...10 V
Corresponds to input
span selection
(DC 10V at 1 mA)
M9104-GGA-5S
3.6 VA
Modulating
DC 0(2) to 10 V
or 0(4) to 20 mA
with field furnished 500 ohm
resistor
4 Nm